The collar is released from rest in the position shown and slides down the fixed rod. Calculate (a) the stiffness k of the spring (which has been initially pre- compressed 50 mm by the light strap and wires) so that its maximum additional deflection equal 190 mm. (b) The nomal force N between the rod and the collar at the end position. U=AT

The collar is released from rest in the position shown and slides down the fixed rod. Calculate (a) the stiffness k of the spring (which has been initially pre- compressed 50 mm by the light strap and wires) so that its maximum additional deflection equal 190 mm. (b) The nomal force N between the rod and the collar at the end position. U=AT

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.170RP: The 320-lb homogeneous spool is placed on the inclined surface. Determine the vertical force P that...

See similar textbooks

Similar questions

A 15-kg uniform disk is placed in contact with the ground and a constant couple moment M = 32 N.m is applied to it as shown. The weight of link AB is negligible. If the coefficient of kinetic friction at D is 0.3, find the angular acceleration of the disk. write the answer in rad/s? but do not write the units. R = 0.25 m A Taylor Answer:
The figure shows the cross section of a uniform 239-lb ventilator door hinged about its upper horizontal edge at O. The door is controlled by the spring-loaded cable which passes over the small pulley at A. The spring has a stiffness of 16.6 lb per foot of stretch and is undeformed when 8-0. If the door is released from rest in the horizontal position, determine the maximum angular velocity reached by the door and the corresponding angle 0. Answer: @max 4.2¹ rad/sec at 8-i
Your answer is partially correct. The figure shows the cross section of a uniform 174-lb ventilator door hinged about its upper horizontal edge at O. The door is controlled by the spring-loaded cable which passes over the small pulley at A. The spring has a stiffness of 12.7 lb per foot of stretch and is undeformed when = 0. If the door is released from rest in the horizontal position, determine the maximum angular velocity reached by the door and the corresponding angle 0. Answer: Wmax = www 4.2' 0.636 rad/sec at 0 = 58.49 O
Please respond as reply as possible, USE THE DATA SHOWN IN THE TABLE. Distances are in centimeters The mechanism shown is used to carry out experimental tests on different industrial springs that are placed between the wall and point A. The rigid reinforcement that holds the spring at A moves through the horizontal beam by means of the 4 frictionless rollers. The piston CD is compressed by stretching the spring at A. For the situation in the position shown the spring is stretched a distance s and has an elongation constant of 2000N / m. The weight of the system can be considered negligible. Determine: 1.The magnitude of compressive force exerted by the piston at the position shown. 2.The magnitude of the force experienced by the bolt at E.
H3
2. Consider the 5-1lb bar with length of 2½ feet and width of 2 inches. Small frictionless bearings are mounted to the ends, constraining the motion of the bar to the horizontal x and y slots. The bar starts at rest at positioned at 0= 45°. If an angular acceleration of 3 rad/s² is desired, what moment M must be applied to the bar? What are the reaction forces at A and B at that instant? Additional question: Does the width of the bar matter, or is it appropriate to consider the bar as a slender rod? Consider errors of less than 2% negligible.
Q. The upper and lower arms of Porter governor are 0.25 m each and are pivoted 30 mm from the axis of rotation. The radius of rotation Is 130 mm. The mass of the ball and sleeve are 3 kg and 38 kg respectively. Find the effort and power of the governor.
In a porter governor the mass of the central load is 18 kgand the mass of each ball is 2kg. the top arms (254) mm while the bottom arms are (304) mm long. The friction of the sleeve is 20 N. If the top arms make 45 deg with the axis of rotation in the equilibrium position, find the range of the speed of the governor in that position
The figure shows the cross section of a garage door which is a uniform rectangular panel 7.3 ft by 7.3 ft and weighing 236 lb. The door carries two spring assemblies, one on each side of the door, like the one shown. Each spring has a stiffness of 71 lb/ft and is unstretched when the door is in the open position shown. If the door is released from rest in this position, calculate the velocity of the edge at A as it strikes the garage floor. omwmwwww B 7.3' 9.2' 7.3' Answer: VA = i ft/sec
A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 780 kg and an average gear-tooth force of 2.20 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset T of the center of mass Gof the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 140 mm, R = 680 mm, 0 = 18°. Detail of contact at B B •G Answer:T= mm
A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 740 kg and an average gear-tooth force of 2.60 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset X of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assumer = 110 mm, R= 695 mm, 0 = 24° Detail of contact at B Answer: X mm
Can the uniform bar of weight W remain at rest in the position shown?