The circuit was in steady state for a long time before the switch was closed. Please calculate Vc, at the given times, where L = 48 mH, C₁ = 10 nF. t=0 VC1 C₁ 5 10 V Vcz 6 nF I t=0 t=0+ t=1s Unit Ve 6.25 V 6.25 5.5 O V Maximum current that will be passing through the inductor after the switch is moved ILmax 2.2 mA

The circuit was in steady state for a long time before the switch was closed. Please calculate Vc, at the given times, where L = 48 mH, C₁ = 10 nF. t=0 VC1 C₁ 5 10 V Vcz 6 nF I t=0 t=0+ t=1s Unit Ve 6.25 V 6.25 5.5 O V Maximum current that will be passing through the inductor after the switch is moved ILmax 2.2 mA

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
List the five capacitor replacement rules.
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in parallel. The circuit is connected to a 240-V, 400-Hz power supply. Find the following values. XL=XC=IR=AIL=AIC=AP=WVARsL=VARsC=IT=AVA=PF=%=
The figure below shows a simple RC circuit with a 3.30-μF capacitor, a 4.40-M resistor, a 9.00-V emf, and a switch. What are the following exactly 9.00 s after the switch is closed? (a) the charge on the capacitor 13.7204 UC (b) the current in the resistor 0.0110522 x Your response is off by a multiple of ten. HA (c) the rate at which the capacitor is storing energy μW (d) the rate at which the battery is delivering energy μW
Q2) What is the total capacitance in Figure? What is the voltage across each capacitor? Vs C₂ 5V 330 pF 220 pF
At 0-, no currrent flows through the capacitors because they are open, how did you combine the capacitors for the voltage divider since it is the capacitance value and not reactance, is it right? Can we just combine the capacitance value? Please explain. I did not understand..
• Circuit diagram needed.• Answer must includecorrect units.
Find the Equivalent Capacitance between P and Q from the figure below
Find the equivalent inductance as seen from the terminals shown in the figure.