The chloride in a 0.2720-g sample was precipitated by introducing 50.0-mL of 0.1030M AGNO3. Titration of the silver ion present in excess required 8.65-mL of 0.1260M KSCN. Express the result of the analysis in terms of percent MgCl2. Molar Masses: MgCl2 = 95.21 %3D

Q: NaOCI to be used in an experiment is available as a 8.5% w/v solution. If the reaction requires 225…

A: NaOCl available for experiment as = 8.5% w/v solution  Required NaOCl = 225 mg  Solution required…

Q: 3. In the following reactions, identify the conjugate acid-base pairs. CHO: + H;0 ++ HC;HO;+ OH…

A:

Q: Which compound will best dissolve in CCI,? Choose your answer from the options below and provide…

A: In chemical, the solubility of chemical substance is the ability of a chemical substance (solid,…

Q: . SUPPLY THE MISSING DATA.WRITE THE CORRECT CONDENSED STRUCTURAL FORMULA AND GIVE THE IUPAC…

A:

Q: In which of the following cases would recrystallization be favored over extraction when purifying a…

A: Recrystallisation is a technique that is used for purifying the non-volatile organic compounds.…

Q: QI. BHs can be made by using Lithium hydride LiH. 6LİH + 2BCI, - BH, + 6LICI If you mix 624 g of…

A: Given data: Mass of LiH = 624 g Mass of BCl3 = 2115 g Mass of B2H6 recovered = 168 g

Q: Consider the compound, C₂H4O₂. (5 pts each) Using the framework below, draw two possible Lewis…

A:

Q: What is the absorbance of 0.1M copper sulfate at 780nm? Please provide re

A: Without any experiment we can say about absorbance of  .1 M copper sulfate at 780nm .But you can…

Q: You are again creating PET (repeat unit molecular weight = 192 g/mol) through reaction of a diacid…

A: The degree of polymerization in polymer chemistry refers to the number of monomeric units in a…

Q: (C3H5OH-water) If a mixture of methanol and water is distilled to maximum theoretical separation,…

A:

Q: Below is shown the results of an adsorption study, where two granulated activated carbons (GAC) have…

A: False. The equations alone do not provide information about the overall performance.

Q: Show that the initial rate law predicted by the reaction mechanism 6-12a- with the first step…

A:

Q: For TLC analysis, a student calculates the following Rf values for her samples: 0.69=aspirin;…

A: The identity of the unknown is to be determined in the given analysis.

Q: c) There are three types of conditions used for methanol manufacture: • high pressure: 250-300 atm;…

A: Dear subscriber ,since you have given the answers to (B) , without part (a) , so, i am assuming ,you…

Q: Activity 2 If the actual laboratory yield is 95.8 g Fe2 03, what is the reaction's percentage yield?…

A: The transformation of raw material into desired products is called the reaction. The raw materials…

Q: The following solutions have equal concentration, which one will show minimum osmotic pressure? a.…

A: Osmotic pressure is the minimum pressure that is required to be applied to a solution in order to…

Q: an you demonstrate the process path for enthalpy 2 (going out)?

A: The enthalpy change of the acetone vapor leaving the condenser is to be determined.

Q: Q2:- If you know that the concentration of the standard solution is 200 mol/L,and relative error =…

A: Write the relation between the absolute error and relative error as follows: relative error =…

Q: Chloroacetic acid (CICH₂ CO₂ H) has Ka = 1.41 x 10-3. What is the value of K, for the chloroacetate…

A: Ka ×Kb =Kwwhere Kw = 1×10-14 Given Ka= 1.41 ×10-3

Q: How long will it take for the concentration of A-B to drop to 0.200 M? provided. [A], = 0.317 M %3D

A: From the linear plot of ln[A] vs t we can determine that the reaction is in first order.  The first…

Q: I need help with this. What does "interpolating in the same table" mean?

A: interpolation is the method to determine the value from a table at conditions which lie between the…

Q: You measure the mixing ratio of a gas to contain 15% ammonia and rest air. The required collection…

A: Ammonia is to be absorbed from the ammonia-air mixture with the help of a scrubbing liquid.

Q: Consider this reaction: A + B products The following data was obtained at a certain temperature. 1…

A: given details: the reaction, A+B→products the data is given, we need to determine the order of the…

Q: don't use third party content 1246. What are the principles of surface-enhanced Raman spectroscopy…

A: Surface-enhanced Raman spectroscopy (SERS) has significant applications in chemical analysis for…

Q: a) What drawback may you observe if you do use water to recrystallize solid Z? b) Now we are left…

A: Given data: Melting point of sample of solid Z = 90-92 0C The solubility of Z at the room…

Q: Q2/ Find F1, F2, and F3 for the system shown below? F3=? 100% Benzene F1=? F2=? 60% Xylene 40%…

A: Benzene is a clolurless or light yellow liquid at room temperature. It has a cyclic structure ,…

Q: Chemical Engineering Question

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Assume the starting melting point of your impure acetanilide was 105-111; and your purified…

A: In the process, purification is one of the high rated processes for any industry. Purification is…

Q: containing 24 mg/L toluene? Note: K = 26.1 and 1/n = 0.44 from %3D

A: In mass transfer we study two different phenomenon one is absorption and other is adsorption. we…

Q: ) How can a mass spectra be interpreted for qualitative analysis? (4) b) How can an NMR spectra be…

A: Steps in interpretation of mass spectra Run the spectra against a database: Databases are decisive…

Q: opedia ge/felder Acetone (denoted as Ac) is partially condensed out of a gas stream containing 66.9…

A: For open steady state system energy balance  Total energy=total heat +total work There are no moving…

Q: Calculate the diffusivity in m2/s of metal X in metal Y at 1142 F. The pre-exponential factor is 2.4…

A: Given data: Temperature = 1142 0F Pre-exponential factor = 2.4 cm2/s Activation energy = 989 cal/mol

Q: 2. What is the rate of the reaction if the concentration of Hydrogen gas went from 0.5 M to 0.1 M in…

A: Note: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: You have been asked to double the check the work of a colleague. She has been working with the…

A: A mixture of hydrocarbon is given.

Q: 1. [Flow equalisation, effect of equalisation on BOD mass loading rate]. Consider the volumet…

A:

Q: Calculate the amount of lime and soda required to soften 25,000 litres of water having following…

A:

Q: Show me the balances for each subsequent system: overall, air conditioner, mixing point, and…

A: Material balance for the subsystem and overall system is to be written.

Q: In Octal Petrochemical company find the first order rate constant for the disappearance of A in the…

A: Initial Volume% of A=80% Final Volume% of A=20% Time taken=3minutes To find: The reaction rate…

Q: If co = 100mg/l and it takes 4 hours to reach a concentration of 10mg/l. What is k? (first-order)

A: In Chemical Reaction Engineering, A first-order reaction is the reaction rate is linearly dependent…

Q: [References] A 0.069 M solution of diphenylamine has a pH of 6.82. What is the value of K, for this…

A: (C6H5)2NH + H2O ↔[(C6H5)2NH2+] +[OH-] DIPHENYLAMINE IS A WEAK BASE AND IT DOES NOT DISSOCIATE…

Q: Discuss the need for a purge gas in TGA

A: TGA stands for thermogravimetric analysis. By TGA , we can characterise the given sample of mixture…