The characteristics of a centrifugal pump operating at 1000 rpm is given by H=41-20002. The system characteristics may be represented by H=24+3200². The units for volume flow rate Q and head H are m³/s and m, respectively. When two pumps operating at 1000 rpm and connected in parallel are used, with the system characteristics remaining unchanged, the operating volume flow rate through the system is m³/s.

The characteristics of a centrifugal pump operating at 1000 rpm is given by H=41-20002. The system characteristics may be represented by H=24+3200². The units for volume flow rate Q and head H are m³/s and m, respectively. When two pumps operating at 1000 rpm and connected in parallel are used, with the system characteristics remaining unchanged, the operating volume flow rate through the system is m³/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: (a) flow rate, in gpm; and (b) horsepower. Assume near-radial entry flow.

Q: A three-fluid system (immiscible) is connected to a vacuum pump. The specific gravity values of the…

A: The gauge pressure value of P1. Given: The specific weight of water is γw== 9.81 kN/m2. The specific…

Q: Two pump impellers with different diameters run at two different speeds under kinematically similar…

Q: Ah against capacity Q pump and system curves for both pumps running on the basis of the O1. Two…

Q: Q2/ Consider the following liquid level system shown below. The flow through the valve is related to…

A: Given Data:Find:Relationship between the head and time.

Q: Steam enters a horizontal turbine at 350 lbf/in2 absolute, 580°C, and 12 ft/s and is discharged at…

A: Given: P1 = 350 lbf/in2 T1 = 580°C = 580 x 1.8 +32 = 1076 oF V1 = 12 ft/s V2 = 110 ft/s T2 = 25°C…

Q: 15. Hydraulic oil with a Sg of 0.91 is pumped horizontally in a 2-in. I.D. distribution line at the…

Q: LR = 5m, LG = 2.5m and LC = 1.1m Q2. The Skylark family of sounding rockets consisted of a number of…

A: The objective of the question is to calculate the Pitching/Yawing moment of inertia and the rolling…

Q: The performance data for a centrifugal water pump are shown in Table for water at 77°F (gpm =…

A: Get the properties of water at a temperature of T=72F. Conversions: Convert all the units into lbm,…

Q: A pump is tested in the laboratory and the following data were obtained. Determine the pump…

Q: ### Based on the study of pressure losses in pumps and pipelines: Q122. Find the catalogued model of…

A: To find a suitable centrifugal pump based on the specified parameters, it is essential to consult…

Q: A 6 kilowatt pump discharges 10 kilogram per second when the pump impeller diameter is 45 centimetre…

Q: The characteristics of a centrifugal pump operatin at 1000 rpm is given by H-41-200Q². The system…

A: Givenpump-H=41-200Q2 when operating at 1000rpmsystem-H=24+320Q2

Q: A certain SSSF control volume with a single inflow and outflow and has an inflow speed V₁ = 200…

Q: A pump has a displacement volume of 6 in^3. It delivers 24 gpm at 1000 rpm and 1000 psi. If the…

A: The displacement volume is The rotational speed is The pressure is The input torque is The discharge…

Q: 2.5-L bench scale bioreactor is used for the production of recombinant P64K protein from Neisseria…

Q: 2 for the system shown in Figure 2, the parameters of pump and motor are as follows: maximal…

A: According to the given information of the system, we have the following parameters which are given…

Q: determine the rotation rate for the smaller , homologus pump . Using ONLY AFFINITY LAWS

A: To calculate the rotation rate of the smaller pumpgiven flow rategiven head of the pumpspeed of the…

Q: The characteristics of a centrifugal pump operating at 1000 rpm is given by H-45-2100². The system…

A: Givenpump-H=45-210Q2 when operating at 1000rpmsystem-H=28+320Q2The validity of the pump simmilarity…

Q: Determine required input power to motor [1.64 kW]

A: As per policy, we can solve the first problem from multiple questions.

Q: A pump, geometrically similar to the 12.95-in model inFig. , has a diameter of 24 in and is to…

A: For water, ρ1 = 1.94 slug.ft3For gasoline, from Table A.3, ρ2 = 680 kg/m3 = 1.32 slug.ft3 From…

Q: The characteristics of a centrifugal pump operating at 1000 rpm is given by H=45-21002. The system…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

The characteristics of a centrifugal pump operating at 1000 rpm is given by H=41-2000². The system characteristics may be represented by H= 24 +3200². The units for volume flow
rate Q and head H are m³/s and m, respectively. When two pumps operating at 1000 rpm and connected in parallel are used, with the system characteristics remaining unchanged, the
operating volume flow rate through the system is m³/s.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A Pelton wheel performance data are collected in the following table. Turbine speed (RPM) 3000 Shaft torque Water supply line pressure (bar) Water flow rate (L/min) (Ncm) 2.4 18.4 If water supply pipe diameter is 25 mm and turbine wheel diameter is 70 mm, calculate the hydraulic head in m, jet velocity in m/s, speed ratio, hydraulic power in W, mechanical power in W and efficiency of the turbine. What is the optimum speed (RPM) of the wheel (for maximum power)?
I want you to draw the HGL and EGL using the second picture.
Energy Equation Problem
For Questions 3 to 5 A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q^2), in feet BP = (0.0521Q^3) + (1.250^2)+(11.042Q) + 134.5, in horsepower where Q is in ft^3/s. Question 3 If a single pump is used to deliver water of a system which requires a total of 8 ft^3/s, what is the efficiency of the pump (in %)? Take the specific weight of water to be 62.4 lbf/ft^3. Round your answer to 2 decimal places.
A centrifugal pump has the following characteristics as shown in Table 1. Table 1: Pump characteristics Q(m3 /s) 0.033 0.029 0.027 0.0235 0.020 0.017 0.0133 H(m) 40 60 66 75 80 84 90 Efficiency % 20 45 55 68 75 66 45 The pump is used to pump water from a low reservoir to a high reservoir through a total length of 1100 m of pipe 250 mm in diameter. The difference between the water levels in the reservoirs is 25 m. Neglecting all losses except friction and assuming λ=0.042, calculate: i. The discharge and head at the duty point for the pump. (20) ii. The efficiency at the duty point. (5) [2
A scale model of a pump has been tested and the following results obtained. Impeller diameter (D) 110mm Power input (P) 2.5kW Speed (N) 1500 r.p.m. Flow (Q) 14.5 litres/sec Head (H) 17m Efficiency (E) 60% You are to determine the speed and size of a geometrically similar pump which would deliver a flow rate of 25 litres/sec against a 22m resistance head. Determine the power input required by this pump.
For a 6.25-inch Model 4075 pump operated at 1160 rpm, if 450 GPM of water is to be delivered, what will be the estimated pump head in ft? HEAD IN FEET 30 25 0 0 0 10 O 6 ft 7.25" (184mm) 20 7.00" (178mm). 6.75" (171mm). 6.50" (165mm)] 15 6.25" (159mm). 5 O 16 ft O 20 ft O 12 ft aco® L/SEC 5 OT 10 Model 4075 FI & CI Series 15 -6-6 ⁰ dº 20 ANA 888 778 25 REQUIRED NPSH do 1160 RPM November 1, 2010 K ・dº- [M 90 do 30 8800 81 1HP(.75KW) DeJ kin do 60% 35 do 50 Curve no. 2175 Min. Imp. Dia. 6.25" Size 5 x 4 x 7.0 40 45 3HP(2.2KW), 2HP(1 5KW) 5HP(1 1KW)> CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 L 75 150 225 300 375 450 525 600 675 FLOW IN GALLONS PER MINUTE NOWONG FEET 15 12 7 6 2 1 NPSH 758 50 5 HEAD IN METERS 45 586888 KPO 60 40 20 10 LO HEAD IN KILOPASCALS
a) Develop an equation for the head (in ft) developed by the pump described by the chartas a function of flow rate (in gpm) when the pump uses a 9 ¾” impeller. b) Develop an equation for the pump efficiency as a function of flow rate (gpm) when the pump uses a 9 ¾” impeller.
Hydrodynamics pumps 5. A centrifugal pump has r1 = 6 in., r2 = 12 in., b1 = 3 in., b2 = 2 in., β1 = 20°, β2 = 10° and rotates at 1200 rev/min. If the fluid is water at 60°F, estimate the theoretical (a) flow rate, in gpm; (b) the head in ft; and ( c) the water horsepower, HP. Assume near-radial entry flow. a. flow rate Answer : ____________________ gpmb. head Answer : ____________________ ftc. water horsepower Answer : ____________________ HP
i need ans very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
Hydro electric station is installed to utilise 30 ma/sec of water of a river at a head of 7.5 m. If 85% turbine efficiency can be counted on, (i) is it feasible to develop this power by two turbines with rpm not less than 50, the turbine having specific speed not greater than 540 rpm ? (ii) what type of runner will be used ? (iii) what is the diameter of runner if the speed ratio is 0.85? [(i) N = 156'5 rpm, .. yes (ii) Kaplan (iii) P25 m]
m³/s. Two pump impellers with different diameters run at two different speeds under kinematically similar conditions using water. Assume that the pump similarity rules are valid. The first pump impeller has a diameter of 0.2 m, a rotational speed of 1200 rpm and volume flow rate of 0.06 m³/s. The second pump impeller has a diameter of 0.4 m and a rotational speed of 2100 rpm. The volume flow rate through the second pump impeller is