The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 2.3 kN when 0=31°, determine the force P required on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth. Assume a = 90 mm, b = 590 mm. T₁ Answers: P= 8 i T2= Mi a A B kN kN 6 صوام T2₂

The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 2.3 kN when 0=31°, determine the force P required on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth. Assume a = 90 mm, b = 590 mm. T₁ Answers: P= 8 i T2= Mi a A B kN kN 6 صوام T2₂

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Knowing that the average normal stress in member EF of the Pratt bridge truss shown must not exceed 8.99 ksi for the given loading, determine the cross-sectional area (in sq. in) of this member that will yield the most economical and safe design if h = 11.7 ft and P = 92.21 kips. Round off the answer to five decimal places. 010.png В D F h H C E G -on-- 9 ft→9 ft→9 ft→-9 ft- P P
A hollow shaft made of red-brass copper (G = 37 GPa, shear yield strength = 150 MPa) is sandwiched between two solid shafts made of the same material. End A is fixed to a rigid wall and torques are applied to the shaft as shown. 75 kNm d₂160 kNm A d₁ L₁ B Use the following values in your working out: L₂ L₁ = 1.5 m L3 = 2.2 m d₁ = 1 m d₂ = 0.7 m d3 = 1.2 m C d₂ 3 L3 130 kNm D a) Draw a torque diagram for the entire shaft. b) Determine the maximum allowable inner diameter for the hollow section of the shaft, to the nearest mm. c) Determine the maximum length of L₂ (to the nearest mm) that will ensure the angle of twist of D relative to the wall is less than 2°. Use your value from part b for the inner diameter of the hollow shaft. d) By estimating relevant load(s), dimensions, and material properties, calculate the approximate angle of twist between two (non-coincident) points on the object shown below. Clearly state all assumptions, including the location of the chosen points.
A solid 2.95 in. diameter shaft is subjected to a torque of T = 305 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point Hon the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. N Answer: (a) Op1= i Op2= i A Tmax in-plane i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
Please solve with FBD a proper explanation is a must.
An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R, = 30 mm as shown in the figure. The length I of member is 3 m. MT R Ri If a G, = 77.2 GPa G, = 27 GPa and torque of M- = 76 kN. m S appirec o rdICE TWISting in the memper Determine the maximum shear stress in the tube
Problem Solving: Solve the problem with complete solution in landscape orientation by placing it in a short coupon bond and avoid erasures. 1. The blocks shown are connected by flexible. inextensible cords passing over a frictionless pulleys. At A the coefficient of friction are fs = 0.30 and fk =0.20 while at B they are fs = 0.40 and fx =0.30. Compute the magnitude and direction of the friction force acting on each block. CUID 18 1 lupi 300 evenidos to sheq nobeng ella sit 200 bile owow 4900 OT YOU DEMISIA B
Part 2,3,4
please draw a proper free body diagram and answer in complete solution
Consider the frame in (Figure 1). The crate weighs 550 lb. Follow the sign convention. Figure 4 ft O] Al B 1.5 ft 1.5 ft 1.5 ft 1.5 ft . F 6) C . E D 1 of 1 0.4 ft Determine the normal force at point F. Express your answer in pounds to three significant figures. Np = Submit ▼ Part B VE ΑΣΦ Vp = Request Answer Determine the shear force at point F. Express your answer in pounds to three significant figures. vec IVE| ΑΣΦ | | vec 1 当 ? ? lb lb
FE.Question 3.KK
Urgent please solve quickly. a = 10 , b = 7 solve this question about this information. Extra information: Take both loads 35 kN
78.75 мра 33.61 MPa 22.11 MPG Determine @ Omax Omin Tmax (@s, @p) sketch the result JLULL e pain wel, w un pipar places an B , (b) the stress components exerted on the element obtained by rotating the given element clockwise through 30°. Sketch the result