the center of the circle divided by two. the radius of the circle O the bottommost point of the circle the topmost point of the circle O the rightmost point of the circle divided by two

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: Question 29 Which of the following can change the hardness of a material? O Manufacturing process O…

A:

Q: Find the center (xc, yc) of the given thin plate? Need only handwritten solution only (not typed…

A:

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 18…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: v to find angle alpha??

A: To find angle alpha

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: Briefly write down the  steps on how to generate (sketch) an involu

A: Involute Profile

Q: Draw the front, Side and top

A: We need to draw three orthographic projection views.

Q: What are the 2 things that need to be calculated to draw Mohrs Circle?

A: The two things that are needed to be calculated to draw mohrs circle are: 1.Normal stress. 2.Shear…

Q: 20 30 R15 5-Ø10 R10 Ø40 10 40 40 Figure 1

A:

Q: 30r 20dls 20 10r 20 20 30 150 100

A:

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: where is the T-S diagram

A: Rankine Cycle is a ideal cycle for producing net work output in thermal power plant where water is a…

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Place the labels with the most accurate description on the micrograph at locations A, B, and C, as…

A: given; Place the labels with the most accurate description on the micrograph at locations A, B, and…

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: Name the following figures.

A: Pneumatic Cylinder Pivot Bracket with rigid bearing AB7

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: Draw a complete shearing force and a bending moment diagram. Show detailed calculations Use the last…

A: F=54 KNTo determine:Shear force diagramBending moment diagram

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: What is the angle of reference for Mohrs Circle?

A: The Mohr circle is a diagrammatic representation of normal stress and shear stresses acting on the…

Q: Analytically determine the maximum linear displacement of the cutting blade .75 S0 crank blade Your…

A:

Q: Can you draw the OBLIQUE SECTION VIEW of this figure?

A:

Q: The equation of the unit circle is _______________.

A:

Q: Q1) Determine the design angle for strut AB so that the 400-lb horizontal force has a component of…

A:

Q: To make the circle in an Isometric drawing which geometric option we select from menu bar and why?…

A: 1.To make an isometric drawing of circle we select it from menu bar because we do not have any…

Q: i need the answer quickly

A:

Q: Give the horizontal and vertical distances from the upper left corner of this part to the center of…

A: The depth and dimension for the slot is 0.243 and for chamfer 0.089 depth. Hole A X…

Q: question: The degrees of freedom of the calculation package in the figure?

A:

Q: Problem A person is doing leg exercises where a 100N weight linked via a pulley is attached to their…

A: Given: The weight linked with pulley:=100 N So the tension in the cable will be→T=100 N Weight of…

Q: Draft and annotate the 2D sketch of cover using AutoCAD and mention all the dimensions. Colour the…

A:

Q: An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do…

A:

Q: If you have a half circle made of steel and the other half of wood, is the center of the circle…

A:

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: Isometric View Top View Front View Right Side Section View

A: Given: Front view is assumed to in the direction shown below,

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.