The carrier system in the figure has fixed support at point C and is loaded with vertical P load from point B El A A. The lengths of the rod arms are equal and they are L and the bending stiffnesses are written on them. Find the rotation of point B accordingly. 2L 2EI Note: Only the bending moment effect will be considered.

The carrier system in the figure has fixed support at point C and is loaded with vertical P load from point B El A A. The lengths of the rod arms are equal and they are L and the bending stiffnesses are written on them. Find the rotation of point B accordingly. 2L 2EI Note: Only the bending moment effect will be considered.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Number 6 please
Solve last 2 parts
A simply supported beam ABC is loaded at the end of a bracket BDE (see figure). D (Use the deformation sign convention. When entering expressions, use the following as necessary: P and L.) Draw the axial-force diagram for ABC. N N State expressions for the minimum and maximum values of the axial force Mx). Nain = max Draw the shear-force diagram for ABC. Vrur 00 State expressions for the minimum and maximum values of the shear force Vx). min V = max Draw the bending-moment diagram for ABC. M M OMeen O OMin State expressions for the minimum and maximum values of the bending moment M(x). Mmin = %3D 'max
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15000 ksi] rods, and a solid steel [E = 32000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.62 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.42 in. Assume L₁-31 in and L₂-60 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 18 kips is applied. (1) Answers: 0₁ = 6 = i IM L2 (2) B P (1) ksi. ksi. Li
Usin FORCE METHOD of Statistically Indeterminate Structure, determine the reactions at the supports and then draw the moment diagram. Assume A is fixed. EI is constant.
The bending moment diagram is constant for an interval of a beam then the crossponding shear force diagram is an inclined straight line. A curved line. A line parallel to the axis. A zero line
9 Consider the plane truss with load Pas shown in the figure. Let the horizontal and vertical reactions at the joint B be Hg and V, respectively and Vc be vertical reaction at the joint C. 2 exhoM S SLO 60° - II B A 60° D L 60° F 60° KLA G P с Which one of the following sets gives the correct values of VB, HB and V? (a) VB = 0; HB = 0; Vc = P (b) VB P/2; HB = 0; Vc = P/2 (c) VB = P/2; HB = P (sin60°); Vc = P/2 (d) VB = P; HB = P (cos(60°); Vc = 0 [2016
A beam is loaded and supported as shown. Use the double-integration method to determine the reactions at supports A and B. Assume wo = 10 kN/m and L = 9 m. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated. Cut a cross-section through the beam and draw a free body diagram to the left of the cut. Determine the internal bending moment in terms of Ay. Check your equation by solving for M(x) at x = 4.5 m. Answer:Mx=4.5m = kN·m + m Ay
SOLVE USING THREE MOMENT EQUATION
Consider the distributed loading acting on the frame structure which is pin-supported at B and D:a. Calculate a the free coefficient in the distributed load function w(y). Make sure to provide its proper units as well.b. Calculate the resultant force from the distributed load and where it acts along member AB. c. Show a complete and labeled free-body diagram(s) of the structure with the distributed lod replaced by a single concentrated force.d. Solve for the support reactioncomponents Bx, By, Dx, Dy on the frame at the pin-support locations B and D.
This is statics of rigid bodies. Show a step by step solutions.
9 Consider the plane truss with load Pas shown in the figure. Let the horizontal and vertical reactions at the joint B be Hg and V, respectively and Vc be vertical reaction at the joint C. 2 exhoM S SLO 60° - II B A 60° D L 60° F 60° KLA G P с Which one of the following sets gives the correct values of VB, HB and V? (a) VB = 0; HB = 0; Vc = P (b) VB P/2; HB = 0; Vc = P/2 (c) VB = P/2; HB = P (sin60°); Vc = P/2 (d) VB = P; HB = P (cos(60°); Vc = 0 [2016