Problem 1. Concentrated load P, at B and difference AT(x) are applied to circular bar with Young's Modulus E and thermal expansion coefficient a. The diameter of segment AB varies linearly from D at A to 2D at B. The temperature difference A7(x) is applied to segment BC. (a) Find the reaction forces at A and C. (b) Find the deflection of point B.

Q: Can you add the datum line in the illustration and make a bettter illustration based on solution

A: Given, Angle made by nozzle = 45o Horizontal distance = 15 to 20 m

Q: y 130 mm 30 mm 30 mm -40 mm 40 mm-

A:

Q: Determine the Centroid of 3 Areas.

A:

Q: 5. Find diameter y. All dimensions are in millimeters. 1 + 19.30 DIA 118.00 -३०

A: Tapered beam with larger diameter at AB = 19.3 mm  Length of beam ,L = 118 mm  Tapered angle = 3°…

Q: Determine number of external indeterminacy

A: Given data : Number of external support reaction (R)=3+3=6 m=Number of member connected at hinge…

Q: 10 + 5x < 6+3x

A:

Q: Compute Ix for the region shown. y 2 18 2-5--5- -2 -8 8. Dimensions in inches

A: The area is divided into the standard areas as shown below.

Q: Determine the ỹ coordinate. y b. = ky? a

A:

Q: Locate the centroid 10 mm 20 mm 10 mm 10 mm 20 mm 50 mm y

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: Describe briefly the T-v Diagram.

A: The TV diagram refers to the Temperature-Volume diagram for a particular substance. The diagram…

Q: A C L- (2) B "1-12- -L/2→ C x

A:

Q: Determine y for the area shown y 1" 1" in .5" 1" 2" 2" X

A:

Q: From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the centroid, (C),…

A:

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: Find the domains of: f(x)=- x - 9 a. {x\x€R, x#9} b. {x|x€R, x#-3, x#3} c. {x|x€R, x+-3, x # 3, x #…

A: Hello dear this is the solution of your problem The answer is found to be Option (b)  For…

Q: For the following items, answer whether the multiview projection matches the isometric drawing depic…

A: The given figure shows the different items, it is required to state whether the Multiview projection…

Q: +y") dx ly

A:

Q: Locate the centroid y̅ of the area.

A: Draw the figure. From the figure, dA = y dx

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: -0129 -077 R26

A:

Q: where did 3sqrt of 2 came from?

A: Given, A structure with carrying varying load   To find : Where 32 came from.

Q: The block of mass m1 = m0 is attached to a spring of elastic constant k = (m0g)/H and natural length…

A:

Q: A Derive the equation for the unit influence line for the reaction at the support B in the…

A: By Muller Breslau method, remove Reaction at support B and place a Load of P as shown in figure. By…

Q: geven that 1-front view 2-top view find the 1-side view 2-front section

A: In engineering drawing, a different type of projection is there the isometric projection is the…

Q: 500 50 60 400 500 50 80 - 340 80

A:

Q: Set CC: Regular pentagon of 35 mm sides rests on HP (horizontal plane) on one of its sides while its…

A: Pentagon side = 35mm1 Rest on HP2 Vertex corner i.e is 35mm3 Side inclined at 60° to Vp

Q: x+sinx 2. limx0 x+cosx

A:

Q: 40 15 60 90 10 45 07 30

A: The Top view is:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.