The breaking stress of a wire depends upon ___________ a) Length of the wire b) Radius of the wire c) Material of the wire
Q: GIVEN) The length of a wire is increased by 1 mm on the application of a certain load. In a wire of…
A:
Q: 1. Explain what is happening at the tensile strength for a metal from a physical standpoint in 1-3…
A: Tensile strength: The resistance of steel to breaking under tensile tension is known as tensile…
Q: he deflection of point B in
A:
Q: The internal torque on the system due to internal force is ___________ a) Increasing b) Decreasing…
A: Zero
Q: 2. Referring to the figure below, the stress in either wire is not to exceed 30 ksi. The cross-…
A: Given,Stress=30 ksiarea of AB=0.4 in2Area of AC=0.5 in2
Q: What is the area of the stock file if a 1.5 x 10 5kg mass presses down 2.5 feet high stock file that…
A:
Q: Three boards were suspended in three ways which of the following options is correct for tensions…
A:
Q: 01: Using direct stiffness method, determine the structure stiffness matrix of the beam. 10 ft hinge…
A: the direct stiffness method is based on a couple of simple concepts, the first we’ll consider is…
Q: What can be said about the curves in the stress-strain graph given below Strain A Polymer A isa soft…
A:
Q: me rigid pipe is supported by a pin at A and an A-36 steel guy wire BD gure Part A 4 ft био μA B…
A: Have a look
Q: A rod stretches 0.02 m when a force of 5000 N is applied to it. How much will it stretch if a force…
A: The 1st option is the answer. 0.006mExplanation:Please see the attached image for the solution.If…
Q: 5. A wire made of the same material (Y= 12X100Pa) is cut into two parts, we label it as wire I and…
A: The wire is cut into two pieces. Piece 1 : Length L1 = L , diameter d1= d Piece 2 : length L2 =…
Q: What is the stress? a) It is force per unit area and can be expressed as the ratio of the applied…
A:
Q: empt in Progress When subjected to a force of compression, the length of a bone (compression Young's…
A: Given Compression young modulus ,Yc = 9.4×109 N/m2 Tensile young modulus, Yt =1.6×1010 N/m2…
Q: Question 6 To preserve your two favorite trophies, you have coated both trophies with a 1 mm…
A:
Q: In a tensile test, initial length of the experimental specimen is the final length of the specimen.
A: In a tensile test, the formula of percentage elongation is given by ∆=lf-lili×100 Here, lf is the…
Q: Pls help ASAP
A: Concept: There are three forces that act on the jumper while bungee jumping they are, Force due to…
Q: 1) A 7/8 inches diameter bolt, having a diameter at the root of the threads of 0.731 inches, is used…
A:
Q: elastic plastic, 0 0.002 0.004 0.006 0.008 Strain & (mm/mm) Why is there a common behavior between…
A: Why there is common behavior between plastic and elastic.
Q: Defined as the ratio of the ultimate strength to the specific weight A Specific Strength B Specific…
A: Concept: The Specific strength of a substance (or muscle) is equal to its density divided by its…
Q: Recitation A Bone has a Young's modulus of 18,000 Mega Pascal Under compression, it can withstand a…
A: Solution: Given that Young's modulus E = 1800 MPa Stress = 160 MPa Lenght of bone L = 500 mm =0.5 m
Q: Calculate the force (in N) a piano tuner applies to stretch a steel piano wire 8.2 mm if the wire is…
A: The solution for this question has been solved below..
Q: Q1: A leg has 1.4 m shaft of bone with an average cross sectional area of 3x10-4 m?. If the amount…
A: Original length of the Bone, L=1.4 m Cross sectional area of the bone, A=3×10-4 m2 contracted length…
Q: r end of the steel rod an n the lower end of the ste 0.75 m
A: Given: ∑Mo=00.75Pst=PalPst=2Pal
Q: o is when a force causes compression and the object shrinks * O Inertia compressive stress, O…
A: Answer:- tensile stress Sigma is when a force causes compression and the object shrinks - tensile…
Q: If the deformation produced in 20 mm length rod is 0.085 mm, the strain is equal to: Select one: a.…
A: (d) 0.00425
Q: Hooke’s law states that _________ a) stress is always proportional to strain b) stress is…
A: To find: Hooke’s law states that
Q: QUESTION 18 The stress-strain graphs for materials A and B are shown below. The graphs are drawn to…
A: Given : Stress - Strain graphs for materials A and B
Q: An Aluminum cable of length 2.5 m has 15,000 N tensile force acting on it, if the wire is only…
A: Given data: Original Length (L) = 2.5 m Tensile forcey(F) = 15,000 N Stretch in the spring (ΔL) =…
Q: What is the slope of the tangent drawn to the net force curve at equilibrium distance? Lütfen birini…
A: Required : What is the slope of the tangent drawn to the net force curve at equilibrium distance.…
Q: You are designing a small bridge. Find the minimum diameter of a cable with a tensile strength of…
A: Given data The tensile strength is given as σ=75 MPA. The support load is given as F = 15 kN.…
Q: please calculate and answer this thanks.
A: Step 1: Understanding the Calculation: Force to Support a Load The Problem We have a load with a…
Q: Question 28 -4 The shear modulus of aluminum is 2.40x10¹0 N/m².. An aluminum nail of radius 7.51x10…
A:
Q: 1. A polycrystalline cylindrical rod 120 mm long and having a diameter of 10 mm is to be deformed…
A: Given data: The length of rod is l=120 mm. The diameter of rod is d=10 mm. Tensile force in rod is…
The breaking stress of a wire depends upon ___________
a) Length of the wire
b) Radius of the wire
c) Material of the wire
Step by step
Solved in 2 steps
