A copper wire of length 3-m and 1-mm diameter is subjected to a tension of 5-N. Calculate the elongation produced, if the young's modulus of copper is 11x1010 Pa. 4.34x10-S mm a. b. 0.04 mm 8.68x10-5 mm C. d. 0.17 mm

Q: A road engineer is planning to build an overpass and wants to support a 2.1 × 10° kg load over a…

A: Given that, Length of the column is L = 5.450 m Diameter of the column is d = 73.60 cm = 0.736 m…

Q: a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive…

A: Write the given values with the suitable variables. P=250 kN=250×103 Nb=0.12 md=0.05 mt=0.003 m…

Q: A 2.5 x 105 kg mass presses down 18 inches high stock file that causes the file to deform at 2.7 cm…

A: The area of the stack file. Given, Shear ModulusG=7.4×1010 N·massm=2.5×105 kgdeformationx=2.7…

Q: Humans can bite with a force of approximately 810 N. If a human tooth has the Young's modulus of…

A: SOlution: as given F = 810 N E = youngs modulus of bone= A = 1.5 cm2 = 1.5x10-4 m2 L = 1.5 cm =…

Q: WRK-1: The average cross-sectional area of leg 3 cm² and all of body weight 700 orted of this leg,…

A: Cross-sectional area of leg is Weight of body or the force is The change in length of leg is Young's…

Q: hear stre steel plat rivets and

A:

Q: 10. Young's Modulus for steel is 2.1 x 1011 Pa. A steel cable will break if it is subjected to a…

A: Young's modulus (Y) = 2.1×1011 PaArea (A) = 1.5×10-5 m2Length (L) = 18 m maximum stress = 3000 MPa

Q: Bone has a Young's modulus of about 18 ✕ 109 Pa. Under compression, it can withstand a stress of…

A: Given,  Stress = 157× 106  pa L = 0.45 m Y= 18 × 109  pa

Q: Question 28 -4 The shear modulus of aluminum is 2.40x10¹0 N/m².. An aluminum nail of radius 7.51x10…

A:

Q: A 195-kg load is hung on a wire of length of 3.80 m, cross-sectional area 2.00  10-5 m2, and Young's…

A: According to stress by strain relation , stress is defined as the product of Young's modulus to the…

Q: Q1. A bar of thickness 15mm and having a rectangular cross-section carries a load of 120KN.…

A:

Q: Problem Solving... A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x…

A:

Q: A steel wire, 3.0 m long, has a diameter of 1.0 mm. If a 10 kg load is hung from the wire how far…

A:

Q: 1. A homogeneous 800 kg bar AB is supported at either end by a cable as shown in the figure. Bronze…

A:

Q: An electron (m 9.11x10 kg) accelerates in a uniform electric field E = 1.45 x 10* N/C. What is the…

A: Given that Mass of an electron m = 9.11 × 10-31 kg Magnitude of the uniform electric field E = 1.45…

Q: Calculate the elongation of the cable due to load, if a steel cable of 4cm diameter is used to lift…

A: As per our guidelines, we have to answer only first question if question are not subpart of same…

Q: 7. A wire of length 6.5 m with a cross-sectional area of 0.14 cm2 stretches by 4.5 mm when a load of…

A:

Q: 2. A material is 250 cm long, 8 cm wide and 10 cm deep. The material is subjected to an axial force…

A: Length of the material L = 250 cm  Width of the material b = 8 cm  Depth of the material d = 10 cm…

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).