1. A homogeneous 800 kg bar AB is supported at either end by a cable as shown in the figure. Bronze L= 4 m Steel L = 3 m 10 m a. Set up the equations of stress that is required to solve the problem. b. Calculate the smallest area of each cable if the stress is not to exceed 90 MPa in bronze and 120 MPa in steel.
Q: A 100 m long cable with a cross-sectional area of 1.0 mm² stretches by 5.0 cm when a force of 1,000…
A: Given data, Length of cable l = 100 m. Cross sectional area A=1 mm2=10-6 m2. Amount of cable…
Q: A circular rod of cross-sectional area 2 x 104m² has a tensile force of 80 kN app The stress in the…
A:
Q: P k a P te
A: Shear stress; is a force that tends to cause material deformation by slippage along a plane or…
Q: 10. An aluminum rod is 3.5 m long and 3.25 cm in diameter. A) How much force would be required to…
A:
Q: Q2 The structure shown in the following figure is made up of three blocks. No pin or other…
A:
Q: A road engineer is planning to build an overpass and wants to support a 2.1 × 10° kg load over a…
A: Given that, Length of the column is L = 5.450 m Diameter of the column is d = 73.60 cm = 0.736 m…
Q: Solve the following problems: A mass of 100 kg moves in an acceleration of 10m/sec". Calculate the…
A:
Q: Problem 2. From the given section of a wide flange shown in the figure, it carries a vertical shear…
A:
Q: QUESTION 16 The T-beam is made of a nylon. The allowable stress is 24 MPa in tension and 30 MPa in…
A: The area of the top section will be, A1=80×30 ⇒A1=2400 mm2 And the area of the bottom section will…
Q: 2. Referring to the figure below, the stress in either wire is not to exceed 30 ksi. The cross-…
A: Given,Stress=30 ksiarea of AB=0.4 in2Area of AC=0.5 in2
Q: Part A What is the minimum horizontal force F needed to make the box start moving in (Eigure 1)? The…
A: Mass of block m = 28 kg Let F1 = 16 N Coefficient of static friction μs = 0.47 Coefficient of…
Q: 4. A steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip-ft. Use a…
A: In this question we need to find 1st formula for maximum shearing stress then find the angle of…
Q: 7. A 6.0 m cylindrical steel beam 3.50 cm in diameter supports an overhead walkway. The beam is…
A:
Q: me rigid pipe is supported by a pin at A and an A-36 steel guy wire BD gure Part A 4 ft био μA B…
A: Have a look
Q: The homogeneous wire ABCD is bent as shown and is attach to a hinge at C. Determine the length L…
A: this question is about to measure center of gravity of wire for equilibrium.
Q: of nm?. Given that P=2 kN; aw the FBD of the rigid membe how the forces at A and B with ct senses.…
A: Given:
Q: 2. For safety in climbing, a mountaineer uses a nylon rope that is 58 m long and 1.2 cm in diameter.…
A: Given that: The length of the rope is L=58 m The radius of the rope is d=r2r=1.22=0.6 cmr=0.006 m…
Q: Determine the largest weight W that can be supported by two wires shown in Fig. The stress in either…
A: Maximum weight supported by the given system of wires is equal to the sum of vertical components of…
Q: Two solid cylindrical rods support a load of P = 37 kN as shown in Figure below. R has a diameter of…
A: We know that we first draw a free body diagram of the system given as Now We calculate the angle…
Q: For a constant force, a rope breaks due to stress. Which of the following is useful to reduce the…
A:
Q: Part 1. A force stretches a (first) wire by 2mm. This wire is made of an unknown material and has a…
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: 5. The ultimate strength of a metallic wire for tension is 2.0 x10^8 Pa. The wire was set up with a…
A: Given Maximum Pressure Pmax = 2.0 x 108 Pa Mass m = 200 kg Diameter D = 0.50 cm = 0.50 x 10-2 m
Q: Consider a steel rod with radius r and length L subjected to a constant tensile force T. If the…
A: Given, a steel rod with radius r and length L subjected to a constant tensile force T. We know…
Q: 2. The breaking stress of copper is 210 MPa. What is the maximum force that can be applied to a…
A: Given, Breaking the stress of copper, σb=210MPaσb=210×106Pa Diameter, d=1mmd=1×10-3m The braking…
Q: Mechanical stress is Select one: O a. a change in the relative position of the points of the body,…
A: Mechanical stress is defined as force per unit area , when a load is applied to the material .…
Q: 3. A flat steel bar 150 mm wide by 50 mm thick has axial loads applied at points A, B, C and D as…
A: Solution: The free-body diagram of the forces of the bar in section BC is shown in the figure.
Q: P4. If the cross section of the femur at section a-a can be approximated as a hollow as shown,…
A: Maximum normal stress = 235.98 lb/in2 = 236 psi Detailed solution is given below: Please UPVOTE sir
Q: 1. A cubic-shaped elastic block with side length L = 50 cm is fixed to the floor. An external force…
A: To solve this problem, we'll approach each part step by step.Part (a) Determine the angle ϕThe angle…
Q: A tensile test is conducted on polypropylene at different load rates (1 mm/min, 10 mm/min, 100…
A: Young's modulus is a property that's inherent to the material. so the load applied to the material…
Q: ) For the structure shown, determine the internal loadings acting on the cross-section at point B.…
A:
Q: What is the stress for a wire of 5 m long so that the strain is 2% of 0.2? The cross-sectional area…
A:
Q: 1. A homogeneous 800 kg bar AB is supported at either end by a cable as shown in the figure. Bronze…
A:
Q: For safety in climbing, a mountaineer uses a nylon rope that is 65 m long and 1.4 cm in diameter.…
A:
Q: beyond the maximu Fter some time?
A: Given: What happens when the stress applied to the body is increased beyond the maximum value and is…
Q: 1. A wire of radius 0.8 mm and length of 2.5m is stretched by a force of 49N. calculate the stress,…
A:
Q: 4. A 4.0m-long steel wire has a cross-sectional area of 0.050 cm². It's breaking stress has a value…
A: Area=0.050cm² stress has a value of 0.0065 times its Young's Modulus young modulus for steel: 20*…
Q: A wire stretches from 2000 mm to 2005 mm when a 500-N box hangs from one end of it. The wire has a…
A: Original length of wire (L) = 2000 mm = 2 m New length of wire (L') = 2005 mm= 2.005 m Force (F) =…
Q: The compound bar is composed of brass and copper. It supports the axial loads shown below. Determine…
A: Given: Here are the given data, Brass, d=6.5 inches Copper, d=4.5 inches Fbr=450 lbFco=250 lb To…
Q: of the stud is under compression, and which surface is under tensi op and bottom surfaces are under…
A: The bending can be shown as,
Q: The dimensions of the Shear Strain is Select one: O a. MLT-2 O b. MLT-1 O c. dimensionless O d.…
A:
Q: 2. A Torque of magnitude T = 900 N.m is applied at D as shown. Knowing that the diameter of shaft AB…
A:
Q: Question 28 -4 The shear modulus of aluminum is 2.40x10¹0 N/m².. An aluminum nail of radius 7.51x10…
A:
Step by step
Solved in 6 steps with 6 images