The homogeneous wire ABCD is bent as shown and is attached to a hinge at C. Determine the length L that results in portion BCD of the wire being horizontal. + 200 mm -L· В D 150 mm A
Q: F |A B -
A:
Q: Obtain a value of pi from your graphs and compare with the 'theoretical' value.
A:
Q: A metallic bar of cross-section Ao = 103 mm² and length Lo = 0.1 mm, is subjected to = 1600 N, the…
A: Given: The cross section area of the metallic bar is 103 mm2. The original length of the…
Q: A body of mass 500 kg is suspended on the free end of an iron wire of length 3 m and cross-sectional…
A:
Q: educed to (L/3) and radius to (r/2), its Young's ength (L) and radius (r) is (Y). If the length is…
A: To find-The Young's modulus=?Given data-Original Young's modulus=YOriginal length=LOriginal…
Q: One end of a uniform = 4.10-m-long rod of weight w is supported by a cable at an angle of 8 = 37°…
A:
Q: How is the bulk modulus at equilibrium distance Beg related to the cohesive energy of the crystal u…
A: The bulk modulus (B) of the material is given using the following expression. But the pressure P…
Q: A copper wire of length 3 m has a diameter 1 mm. If weight of 10 kg is attached to one end of wire,…
A: We need to compute-(i) Extension produced (l)=?(ii) Lateral contraction=?The data given as-Length of…
Q: Determine angles Cable to main tain W=80N quilibrium · smooth R. 140
A: Given information: The weight of the body A (Wa) = 80 N The weight of the body B (Wb) = 70 N The…
Q: 2. Referring to the figure below, the stress in either wire is not to exceed 30 ksi. The cross-…
A: Given,Stress=30 ksiarea of AB=0.4 in2Area of AC=0.5 in2
Q: 1) Determine the largest weight W that can be supported by two wires shown in Fig. below. The stress…
A: Draw the free body and force diagram as below. As given, The stress on both wires,…
Q: A horizontal boom 11.5 M in length, AE is supported by guy wires from A to B,C and D. If the tensile…
A:
Q: The arm of a starter is held in the "ON" position by means of an eleetromagnet. The torque exerted…
A:
Q: 5. A wire made of the same material (Y= 12X100Pa) is cut into two parts, we label it as wire I and…
A: The wire is cut into two pieces. Piece 1 : Length L1 = L , diameter d1= d Piece 2 : length L2 =…
Q: Two parallel wires A and B are fixed to rigid support at the upper ends and subjected to same load…
A:
Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…
A:
Q: : Two wires of equal cross-section one made up of aluminium and other of brass are joined end to…
A: We need to find- Ratio of lengths of two wires LAlLbrass=? The data given as-…
Q: copper wire of length 3 m nas a diameter 1 mm. If weight of 10 kg is attached to one end of wire,…
A: To find- (1) Extension produced (l)=? (2) Lateral contraction =? Given- Length of wire (L)=3 m…
Q: Two forces of magnitude TA= 7607 lb and TB= 14617 lb are applied as shown to a welded connection.…
A:
Q: Determine the minimum required width b for the beam and loading shown. For wood, σem =16, τem =38…
A: Draw the FBD of the beam.
Q: Two aluminum plates, each having a width of b = 5.6 in. and a thickness of t = 0.725 in., are welded…
A:
Q: How can the Fastener Spacing be determined?
A: Introduction: The distance between fasteners should be at least thrice the fastener diameter.
Q: Both portions of the rod ABC are made of an aluminum for which E5 70 GPa. Knowing that the magnitude…
A:
Q: The table below shows ultimate tensile strengths (Fu ) and Young's moduli (Y) for tungsten (W) and…
A:
Q: Auniform rod is attached to a wall by a hinge at ts base. The rod has a mass of 1.5kg, a length of…
A: Given, Mass =1.5 kg Length = 1.8 m Angle = 21∘
Q: Find the forces produced in Bars 1, 2, and 3 of the truss shown due to the action of a ball of…
A:
Q: Drawa FBD of node B and using jolent method at B determine the forces in members BA and Bc. Note…
A: Answer..
Q: e)Differentiate between conservative and non conservative forceś.
A: We have to describe the difference between conservative and non conservative Forces
Q: - A rigid member CBD is supported by a flexible cable AB as shown below. If a force applied to the…
A: Take point C as origin and vertical as y axis. Initial coordinate of point B =0,300 Initial…
Q: A B C 300 μm Which denotes the apical meristem in roots? B C D A D
A: The correct answer is B.Explanation: The image you sent is a labelled diagram of the tip of a root,…
Q: A copper coin can scratch a feldspar true or false
A: For this we need to know the hardness of two materials . According toh Mohs scale of hardness the…
Q: 26 64 ers: 1905 B 216 kg -406.9 N N N
A:
Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…
A:
Q: You are designing a small bridge. Find the minimum diameter of a cable with a tensile strength of…
A: Given data The tensile strength is given as σ=75 MPA. The support load is given as F = 15 kN.…
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 1 images