The box beam in figure below supports the concentrated loads 2P and P. Compute the maximum allowable value of P if the working stress in bending and shear are 1000psi and 100psi, respectively. 2P 8 in. B. D A E 8 in. 10 in. 5 ft 5 ft 5 ft - 6 in. 0.5P 2.5P 1. Maximum value of P that can be applied safely is?

The box beam in figure below supports the concentrated loads 2P and P. Compute the maximum allowable value of P if the working stress in bending and shear are 1000psi and 100psi, respectively. 2P 8 in. B. D A E 8 in. 10 in. 5 ft 5 ft 5 ft - 6 in. 0.5P 2.5P 1. Maximum value of P that can be applied safely is?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E=2× 10° N/mm. The elongation of the bar will be mm mm mm
A frame is built with members ACB and DC to support load P as shown. Member DC has a rectangular cross section with width of 25 mm and thickness t. Stress-strain curve for the material of which the member DC is made is also provided below. a. Determine the thickness t so that member DC does not yield. (You can assume same behavior for compression and tension)b. Determine the diameters of the pin A and D if allowable shear stress for pins is ???? = 40 ???.
The steel beam has the cross section shown. The beam length is L = 4.2 m, and the cross-sectional dimensions are d = 360 mm, bf = 180 mm, tf = 16 mm, and tw = 6 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 210 MPa.
NEED ANSWER ASAP!! A so-called "trapeze bar" in a hospital room provides a means for patients to exercise while in bed (see figure). The bar is 2.1m long and has a cross section in the shape of a regular octagon. The design load is 1.6kN applied at the midpoint of the bar, and the allowable bending stress is 240 MPa. Determine the minimum height h of the bar. Round to one decimal place. (Assume that the ends of the bar are simply supported and that the weight of the bar is negligible.) hmin=___mm
Calculate the shear stress in MPa at section B A 100 mm F-10EN 10 mm
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B and bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest hundredths.
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 L3=1350 GPa. L2=2150 A L1 E Dia. 1 L1=1350 Р3-25 P1 L2 Dia. 2 P2=40 P2 P1=105 Dia2=45 L3 P3 D D 35 mm o Dia1=60
need answers pls and solutions asap, thank you!