The bent shaft is fixed in the wall at A. If a force F is applied at B, determine the stress components at points D and E. Take F = 13 lb and θ= 45 degrees a) Determine (σD)y b) Determine (τD)yx c) Determine (σE)y d) Determine (τE)yz

Q: .

A: Find outA. Determine the shear stress component acting on the inclined plane AB. solve the problem…

Q: , If the shown pipe is subjected to the two force components at its end as shown, determine the…

A:

Q: The block is subjected to axial loa normal tension developed at poir the distribution of the normal…

A:

Q: 600 mm B 800 mm P Part of a control linkage for an airplane consists of a rigid member CB and a…

A:

Q: The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the…

A:

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: Q3) Show the state of stress at points A and B on the assembly at section 400 mm а-а. a 200 mm AB…

A: Write the given data: The load in the x-direction will produce twisting couple on the vertical…

Q: Determine the stress in the cable BC if the mass of the cylinder is 250 kg. The cross sectional area…

A:

Q: 2-11. Determine the plastic distorts as shown by the dashed lines. 3 mm y C 300 mm the shear strain…

A:

Q: If the plate distorts as shown by the dashed lines, determine (a) the shear strain Ym at corners C…

A: Find shear strain at point C and D Normal strain along diagonals AC and BD

Q: The beam is subjected to the load at its end. Determine the maximum principal stress at point B.

A: Determine normal stress due to axial load Due to shear load there will be bending moment at B…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A: Given: F1 = 7KN   F2 = 6KN  F3 = 2KN     F4 = 9KN

Q: A state of stress at a point A is given by σx = 25 MPa, σy = 122 MPa, and τxy = 60 MPa. Determine…

A:

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

A:

Q: If F1 = 1070 Ib and F2 = 2095 Ib, determine the magnitude of the normal stress produced at point H.…

A: Given: The force, F1 = 1070 lb The force, F2 = 2095 lb

Q: Determine the internal forces at point J when a= = 90°.

A:

Q: Q2: If the block is subjected to the centrally applied force of 600 kN, determine the average normal…

A: Given: the block is subjected to applied force =600 kN we have to find the average normal stress in…

Q: For the given state of stress, determine the normal and shearing stresses exerted on the oblique…

A:

Q: The average normal stress and maximum in-plane shear stress components are determined from the…

A: Yes, the average normal stress and the maximum in-plane shear stress components are determined from…

Q: Ship as

A: Given as, F=50 KN d=50 mm

Q: Determine the internal forces at point J when a= = 0.

A: Given,

Q: The beam supports the loading shown. Determine the state of stress at points E and F at section a-a.

A:

Q: Determine the shear strain gxy at corners D and C if the plate distorts as shown by the dashed…

A: Given data To determine the strain energy at corners D and C if the plate distorts

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kNforce is applied to the…

A:

Q: Determine the average normal stress developed in rod AB if the load has a mass of 50 kg.  The…

A:

Q: The steel rod having a diameter of 1 in. It is subjected to an internal moment of M= 200 lb⋅ft…

A:

Q: Determine the normal stress developed at points A and B. Neglect the weight of the block.

A: The sum of forces in the horizontal direction, ∑FX=-6 kips -12 kipsF=-18 kips The expression of the…

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the…

A: Given, The diameter of AB(dAB) = 4 mm The diameter of BC(dBC) = 6 mm Load (P) = 3 kN For Member…

Q: Using transformation equations of plane stress, determine the normal and shear stress components for…

A: The clockwise angle between the x’-axis and the x-axis is, θ=0.5 rad×180°π=28.65° The stress…

Q: Determine the resultant internal loadings acting on the cross-sections at points D and E of the…

A: The free body of the beam is as follows: Calculate the moment about point A as follows:…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A:

Q: The state of in-plane stress at a point on an element of material is shown. Let |σx| = 370 MPa, |σy|…

A: σx=370 MPaσy=130 MPaτxy=85 MPaθ=25 °then,σx=σx=370 MPaσy=-σy=-130 MPaτxy=-τxy=-85 MPaAngle from…

Q: Qu 1 Determine the normal stress component σx' and the stress component Tx'y' acting on the inclined…

A: From the question, we can identify the following given values:The angle of inclination (θ) of plane…

Q: The solid rod has a radius of 30 mm. Determine the state of stress at points a and b. Write each…

A:

Q: Determine shear strain of each corner: A,B,C,D

A:

Q: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown, determine…

A: Writing equilibrium equations:→∑FY=0 ⇒-P+∫04[(15.x)×(dx×0.5)]=0⇒P=15×23×[x23] 04×0.5⇒P=40 MNNow…

Q: The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC,…

A: Given: The mass of the concrete pipe is m=2 Mg. The diameter of the cable AC is d’=10 mm=0.01 m.…

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 8…

A: Maximum normal stress at the fillet                    rh=1020=0.5wh=4020=2 For that stress…

Q: If the load has a weight equivalent to 5 kN, determine the maximur hormal stress on the cross…

A: Given Data Load is :P=5 kN=5000 N Radius of circle is :r=2 cm=20 mm Distance of CD is : LCD=50…

Q: The bar has a 80 mm by 20 mm rectangular cross section. If P = 90 kN, determine the normal stress…

A:

Q: A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa,…

A: given; σx=8MPaσy=4MPaτxy=3MPa

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.