The beam in the figure below is subjected to a concentrated live load of 15 kN, a distributed dead load of 4 kN/m, and a distributed live load of 8 kN/m. 1- Sketch the influence line for the reaction at C. 2- Sketch the influence line for the shear just to the left of C. 3- Sketch the influence line for the moment at A.

The beam in the figure below is subjected to a concentrated live load of 15 kN, a distributed dead load of 4 kN/m, and a distributed live load of 8 kN/m. 1- Sketch the influence line for the reaction at C. 2- Sketch the influence line for the shear just to the left of C. 3- Sketch the influence line for the moment at A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. Draw the Influence diagram of the given beam. Solve questions D, E and F A 4m D 7m B www 3m C A. Draw the influence line diagram for the reaction at point A. B. Draw the influence line diagram for the reaction at point B. C. Draw the influence line diagram for the MAXIMUM moment at point D. D. Determine the maximum moment at D due to a dead load of 5 kN/m a movir g live load of 20 kN/m and two (2) movable concentrated loads 50 kN and 75 kN 2m apart. E. Determine the maximum shear at A, 7m from point C due to a dead load of 5 kN/m a moving live load of 20 kN/m and two (2) movable concentrated loads 50 kn and 75kn 2m apart. F. Determine the maximum moment at B, 4m from point A due to a dead load of 5 kN/m a moving live load of 20 kN/m and two (2) movable concentrated loads 50 kN and 75kN 2m apart.
APPLICATION OF INFLUENCE LINE: 1 TL. 2m Live uniform load = 8.5 kN/m Live load = 56 kN Dead Load = 5kN/m 2m Im 3m a) Determine the maximum reaction at A. b) Determine the maximum shear at D. c) Determine the maximum shear at E. d) Determine the maximum positive moment at D. e). Determine the maximum negative moment at D. f) Determine the maximum reaction at B. g) Determine the maximum reaction at C. h) Determine the maximum negative moment at E.
The beam in the figure below is subjected to a concentrated live load of 15 kN, a distributed dead load of 4 kN/m, and a distributed live load of 8 kN/m. 1- Sketch the influence line for the reaction at C. 2- Sketch the influence line for the shear just to the left of C. 3- Sketch the influence line for the moment at A. 4- Find the maximum positive moment at A due to the applied loads. 5- Find the maximum negative moment at A due to the applied loads. internal hinge C 4 m 2m 3m
Refer to the propped beam below. Draw the influence line for the vertical reaction at B for the beam in Fig. 9-25a. El is constant. Plot numerical values every 1 m. A -6 m (a) B Use conjugate beam method to solve for the reactions. Plot the numerical values in a table. Draw the influence line diagram for reaction B correctly.
Draw the influence lines for: reaction at A reaction at B reaction at C shear at G
From the given figure; Determine the Influence line, 1) 2) 3) 4) Sm Hinge I 5m 3m 1 Hinge 3m 3m Determine the influence line for reaction at B. Determine the influence line for reaction at D. Determine the influence line for shear at E. Determine the influence line for moment at E. Determine the influence line for reaction moment at G.
2.Determine the Influence Line for the reactions at each support (Ay, Ma, Cy), shear at point B and moment at point B WITHOUT EQUATIONS. Also, apply the influence lines and determine the values of the reactions in kN. 100 kN 60 kN/m A C 6 m 4 m Internal hinge
1. Draw the influence lines and determine the maximum reaction at A and B, maximum moment and at midspan. Considering the given moving loads. 6 k 4 k 2 k 2 k 3 ft 6 ft 4 ft Bf 40 ft
Draw the influence lines for the structure shown below,mark the values at peaks. (1). A 2m D (a).reaction at point B (b).shear at point D (c).moment at point D 4m B
Draw the influence line diagrams for vertical reactions at supports B and C of the indeterminate beam as shown in Figure 4. El is constant. Plot numerical values at every 2 m. A + 2 m B 6 m с
A. C G 3. 1 2 1 1 Using the Miller-Breslau Principle, draw the influence lines for reactions A, B and C. Draw the influence line for shear at G. E