The bar shown made from steel (S = 90 ksi) is subjected to a fully reversed bending moment of 1500 lb.in. Determinethe infinite-life fatigue safety factor for the bar. Given D = 2 in, d = 1 in, h = 0.5 in, r = 0.125 in, Se = 45 ksi.D.MT M

The bar shown made from steel (S= 90 ksi) is subjected to a fully reversed bending mornent of 1500 lb.in. Determine the infinite-life fatigue safety factor for the bar. Given D = 2 in, d = 1 in, h = 0.5 in, r= 0.125 in, Se = 45 ksi. D M T M

The bar shown made from steel (S= 90 ksi) is subjected to a fully reversed bending mornent of 1500 lb.in. Determine the infinite-life fatigue safety factor for the bar. Given D = 2 in, d = 1 in, h = 0.5 in, r= 0.125 in, Se = 45 ksi. D M T M

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Related questions

Q: Using the distortion energy (DE) theory determine the factor of safety for a bar of made of hot…

A: Given Data σx=234 Mpa σy=-175 Mpa τxy=142 Mpa also, Sy=470 Mpa

Q: A bronze c86100 cylinder with diameter d₂ = 60 mm is nested inside a stainless steel tube with inner…

A: We must take into account the stress in both the stainless steel tube and the bronze cylinder in…

Q: What is the total elongation of steel bar having a diameter of 2 in. hanging over with a length of…

Q: Bar of steel, (yield strenght Sy = 559 MPa) is subjected to the following stresses; σx = 176 MPa ,…

Q: Example 1: 14 • A 25 mm square cross-section bar of length 300 mm carries an axial compressive load…

A: Given data, There is a Square bar, s= 25 mm L= 300 mm P= 50 kN =50000 N E= 200 GN/m2 = 200000…

Q: Problem 2. The assembly consists of three titanium (Ti- 6A1-4V) rods and a rigid bar AC. The…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: The lap joint is fastened by 20 mm rivets placed alongside each other as shown along the length of…

Q: Two rods are connected to each other and are restrained at top and bottom. The top portion is steel…

Q: b=3./m a=2.1m (1) B C = 2m (2) P = 80kN C d = 1.8m WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: Answer: The maximum load that can be supported by the structure without exceeding either allowable…

Q: Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 16 in. and…

Q: Compute for the total elongation caused by an axial load of MN kN applied to a bar 20 mm thick…

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P =…

Q: A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN.…

A: Given, P= 400kN= 400000N σ= 120MPa A=14πD2-14π(1002)A=14π(D2-10000) P=σA

Q: The hollow steel cylinder DNGL, fixed on one end, is subjected to two torques and an axial load, as…

Q: The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When…

A: Given: The diameter of rod is .The diameter of hole is .The plate thickness is .The head diameter of…

Q: An axial load of 100 kN is applied to a flat bar 20 mm thick, tapering in width from 120 mm to 40 mm…

Q: Bronze Steel E = 83 GPa E 200 GPa diameter 100 mm diameter 60 mm %3D %3D 1200 kN 900 kN 2.5 m- 3 m

Q: A steel column with an outer diameter of 50 mm and an inner diameter of 40 mm surrounds a solid…

Q: A steel railroad track is laid at a temperature of 15°F with gaps of 0.18 inchbetween the ends of…

Q: Determine the equivalent stiffness constant of the f

Q: tind the stresses in the steel and aluminum rods when the temperature rises to 60 C° and the…

A: Given: The temperature rise, dT = 60 C The intensity of load = 10 kN/m

Q: A solid round bar is to be assembled into a collar by press fitting. The inside radius of the collar…

A: Given Data The inside radius of the collar is: R=50 mm The outer radius is: r=40 mm The facor of…

Q: Q A cylindrical shaft made of steel of yield strength 700 MPa is subjected to static loads…

Q: The initial compressive force of a steel column can be determined by Euler's buckling formula The…

A: Slenderness Ratio =LeqIxA

Q: The steel propeller shaft ABCD carries the axial loads shown in the figure. Determine the change in…

A: The forces are shown in each member below: The internal forces in 3 segments are :- PAB = PBC…

Q: The circular section steel bar bent in L shape is attached to a fixed wall at end A. A force P is…

A: P=3 KN L1=3 m ,L2=2 mσak=400 Mpa τak=200 Mpa FOS (n)=2 Now from diagram Twisting moment…

Q: For the assembly, the temperature rises by 35°C after a load W = 140 kN is applied. Assume the…

Q: A steel rod of diameter D = 50 mm has a tensile yield strength of 345 MPa supports an axial load P =…

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Question

100%

The bar shown made from steel (S = 90 ksi) is subjected to a fully reversed bending moment of 1500 lb.in. Determine
the infinite-life fatigue safety factor for the bar. Given D = 2 in, d = 1 in, h = 0.5 in, r = 0.125 in, Se = 45 ksi.
D.
M
T M

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
1. A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of 50 kN. The material is AISI 1060 hot-rolled steel (?? =370 MPa,?? =680 MPa ). Use a design factor of 2 and determine the dimensions of the square cross section for the following cases. Neglect any stress concentration. a. The rod must support this load for 100 cycles. b. The rod must support this load for 104 cycles. c. The rod must have infinite life.
The bar shown made from steel (Sut = 80 ksi) is subjected to a fully reversed bending moment of 1250 lb.in. Determine the infinite-life fatigue safety factor for the bar. Given D = 2 in, d = 1 in, h = 0.5 in, r = 0.125 in, Se = 40 ksi
If a solid circular rod having an initial diameter D = 0.03 m and initial length L = 0.8 m, is subjected to a tensile force F = 300 kN, the new diameter will be: Given: The rod is made of steel having Young's modulus E = 200 Gpa and a Poisson's ratio = 0.3. Select one: a. Df= 2.993 mm Ob. Df = 10.92 mm Oc. Df= 3.007 mm Od. Df = 30.02 mm Oe. Df = 29.98 mm
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
EHide bl OP=287 N OP=573 N Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.998 mm. determine the applied force F. Select one: OF=10472 N OF=15708 N OF=6283 N O F= 4189N F = 13090 N OF= 5236 N Finish attempt.. US ACTIVITY O Test-Spring 2020-2021 Jump to...
A vertical force P=1200 N of is applied to the bell crank. Determine; a) The minimum diameter of rod CD, if the max. normal yield stress is 6=500 MPa developed in the rod CD, (S=2, safety factor) b) The minimum diameter of pin B, the max. shear yield stress T =270 MPa developed in the pin B that is subjected to double shear. (S=2, safety factor)
Clear my choice Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: O F= 5236 N OF=15708N O F= 13090 N OF=10472 N OF=4189 N O F=6283 N Clear my choice Finish attempt NEXT ACTIVITY MENG360 Test -Spring 2020-2021 Jup to
answer problem 1 only.
Q1: The crank ABCD shown, F=1 kN. The rod is made from wrought-aluminum alloy 2024 heat treated and the fillet radius at the wall is r=4 mm. Consider the transverse shear effect. Find the factor of safety of this crank. rd mm 200 mm De35 mm 25-mm-dia. round rod bent into crank 250 mm -100 mm Fig. 1