Using the distortion energy (DE) theory determine the factor of safety for a bar of made of hot rolled steel with yelid strenght of Sy = 470 MPa with the follwoing stresses: σx = 234 MPa, σy = -175 MPa, τxy = 142 MPa

Using the distortion energy (DE) theory determine the factor of safety for a bar of made of hot rolled steel with yelid strenght of Sy = 470 MPa with the follwoing stresses: σx = 234 MPa, σy = -175 MPa, τxy = 142 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Related questions

Q: Using the maximum-shear-stress (MSS) theory determine the factor of safety for a bar of AISI 1020…

Q: The figure below shows the shaft of an overhang crank subjected to a force P of 3.5kN. The shaft is…

A: Given: The load acting, P = 3.5 kN The factor of safety, n = 2

Q: This problem illustrates that the factor of safety for a machine element depends on the particular…

A: To find: The factor of safety based upon the distortion energy theory for stress element at A and B…

Q: Find the maximum stress induced in the following cases taking stress concentration into account: 1.…

Q: A bar of steel has the minimum properties Se = 40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The bar is…

Q: negligible. Determine the safety factor against yield using Coulomb-Mohr failure theory

A: Calculate the normal bending stress at A.

Q: Consider the shaft and keyway shown in the figure below. The shaft has a diameter equal to d= 48 mm…

A: Given data Diameter= 48mm Torque Tmin = -320N.m Tmax = 1380N.m Find the maximum,…

Q: 2. This bar is made of AISI 1006 cold-drawn steel and is loaded by the forces F = 0.55 kN, P = 4.0…

Q: In the figure above, the shaft has a diameter of 50mm, and the diameter of pulleys C and D are given…

A: To determine the principal stresses corresponding to maximum bending and torsional shear stresses,…

Q: Which steel presents the maximum modulus of resilience UR? UR = 1/2 × ((Sy^2)/E) AISI 4142…

A: Modulus of Resilience:It is defined as the maximum amount of energy that a material can absorb up to…

Q: Part 1) Find the magnitude of shear and normal stresses from the loads shown. The cross section of…

A: Solution: Given Data: P = 400 N T = 1.8 N-m d = 8 mm

Q: Required information steady A bar of steel has the minimum properties Se=40 kpsi, Sy= 60 kpsi, and…

Q: Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load Pat pin…

Q: A steel rod of diameter D = 50 mm has a tensile yield strength of 345 MPa supports an axial load P =…

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.

Question

Using the distortion energy (DE) theory determine the factor of safety for a bar of made of hot rolled steel with yelid strenght of Sy = 470 MPa with the follwoing stresses:

σ_x = 234 MPa, σ_y = -175 MPa, τ_xy = 142 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
The strength-to-weight ratio of a structural material is defined as its load-carrying capacity divided by its weight. For materials in tension, use a characteristic tensile stress obtained from a stress-strain curve as a measure of strength. For instance, either the yield stress or the ultimate stress could be used, depending upon the particular application. Thus, the strength-to-weight ratio RS/Wfor a material in tension is defined as Rs/w= in which a is the characteristic stress and 7 is the weight density. Note that the ratio has units of length. Using the ultimate stress Uas the strength parameter, calculate the strength-to-weight ratio (in units of meters) for each of the following materials: aluminum alloy 606I-T6, Douglas fir (in bending}, nylon. structural steel ASTM-A57.2, and a titanium alloy. Obtain the material properties from Tables [-1 and 1-3 of Appendix I. When a range of values is given in a table, use the average value.
2. This bar is made of AISI 1006 cold-drawn steel and is loaded by the forces F = 0.55 kN, P = 4.0 kN, and T = 25 N•m. Compute factors of safety, based upon the distortion energy theory, for stress elements at A and B of the member shown below. Transverse shear stress ignored here. 100 mm 15-mm D.