The bar shown below is restrained at both ends, i.e. fixed support at both ends. If the bars are unstressed20 degree Celsius,-6a = 11.7 x 10/°C-9-a = 23 x 10/°CE =200 GPaE = 70 GPa%3D1,200 mm?A900 mm?200 kNA300 mm200 mmWhich of the following most nearly givesstresssegment BC whenaxial load of 200 kN directed to left is applied at B at a temperature of 60Select the correct response:21.38 MPa18.68 MPa25.75 MPa11.63 MPa體

Answered: Image /qna-images/answer/36ca12f9-d22e-478b-91db-640ac53386c0.jpg

The bar shown below is restrained at both ends, i.e. fixed support at both ends. If the bars are unstressed at 20 degree Celsius, -6 a = 11.7 x 10/°C a = 23 x 10°/°c E = 200 GPa E = 70 GPa %3D %3D 1,200 mm? A 900 mm2 200 kN A 300 200 mm mm Which of the following most nearly gives segm BC when an axial load of 200 kN directed to left is applied at B at a temperature of 60 Select the correct response 21.38 MPa 18.68 MPa 25.75 MPa 11.63 MPa 體

The bar shown below is restrained at both ends, i.e. fixed support at both ends. If the bars are unstressed at 20 degree Celsius, -6 a = 11.7 x 10/°C a = 23 x 10°/°c E = 200 GPa E = 70 GPa %3D %3D 1,200 mm? A 900 mm2 200 kN A 300 200 mm mm Which of the following most nearly gives segm BC when an axial load of 200 kN directed to left is applied at B at a temperature of 60 Select the correct response 21.38 MPa 18.68 MPa 25.75 MPa 11.63 MPa 體

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the truss structure and the loading given below. a) Compute the average axial stress on member AB, b) compute the average shear stress at the pin of connection A. d- 20 mm 600 mm 50 mm -S00 mm 60 kN 25 mm | I 20 mm 30 mm I20 mm 25 mm TOP VIEW OF MEMBER AB d = 30 mm
Determine the kind and magnitude of bending stress, in MPa, of the fiber 70mm below the neutral axis at distance 2.5 meters from support at A.
Maximum Deflection Calc
For ABC beam with elasticity module E, inertia I; a) Find the reaction forces at point a b) Find the reaction forces at point b
For the truss structure in figure 6, draw the appropriate primary structure under unit loads of redundant. Write the compatibility equation 30 kN D E 耳。 A 3m Ay V20KN 3m |By 3m
The beam is loaded as shown. Determine the dimension of the square beam if the maximum flexural strength at point B is 50 MPa. Show all necessary solution.
Example 2 of Method of Sections: Determine the force in member EB of the FBD of the roof truss shown in the Figure below. Indicate the member in compression (C) or in tension (T). 1000 N 3000 N 1000 N E 1000 N 2 m -2 m -2 m -2 m 4000 N 2000 N
A steel column carries an axial load of 819 kN and a moment of 63 kN-m at the top and moment at the bottom which is only70% of the moment at the top. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties: A = 13172 mm2 rx is 109 mm ry = 94 mm Sx = 1200 x 103 mm3 K = 1.0 L= 3.6 m E = 200,000 Mpa Fy = 248 Mpa Use NSCP specification for compressive stress and Fb =148 Mpa. Determine the Compressive Stress if Axial load only existed.
The frame shown below is subjected to an applied Point Load of 27kN and a Uniformly Distributed Load of 3kN/m and is supported at A by a pinned connection and at B by a roller connection. Calculate the vertical support reaction at B. Give your answer in kN to 2dp. 3m 3m PL UDL 5m A
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
Based on the bridge truss show below determine the force acting at members DF, GI, and LM using method of section.
For the exact in the figure tensile strength = 8000 N / cm ^ 2 compression safety = 3000 N / cm ^ 2 calculate the largest Mx moment that the section can carry.