The bar in the figure is made up of two pieces glued together with glue, at the acde board. The allowable stresses of the pieces are oacde =74.85 kg/cm2 and tacde =40.85 kg/cm2 for normal and shear stresses respectively. The resistance of the glue is oadm=51.05 kg/cm2 for tensile stresses and tadm=34.05 kg/cm2 for shear (in the acde plane). Once the allowable stresses of the material of the bar and of the glue are known, What is the minimum value that the width "b" of the bar could take? square section?

The bar in the figure is made up of two pieces glued together with glue, at the acde board. The allowable stresses of the pieces are oacde =74.85 kg/cm2 and tacde =40.85 kg/cm2 for normal and shear stresses respectively. The resistance of the glue is oadm=51.05 kg/cm2 for tensile stresses and tadm=34.05 kg/cm2 for shear (in the acde plane). Once the allowable stresses of the material of the bar and of the glue are known, What is the minimum value that the width "b" of the bar could take? square section?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three parallel vertical rods of equal length (L-2m) support a rigid beam AB to which a force (P-40kN) is applied. The middle rods is shorter than its design length by (A-0.2 mm). During operation the temperature of the assembly may rise by (20°C). Find the stresses in each rod. 1.5 m m Сорper A=200mm E=100GPA a=17x10 Steel Steel A=100mm E=200GPA A=300mm E=200GPA a=13x106 a=13×10C 0.2mm B A 0.25m P-40KN
HWK 4-2.2-3: Find the shear stress about the neutral axis if V = 2000k
A reinforced concrete column is constructed of 12 1-in-diameter steel rods. Calculate the force maximum allowable P that can be applied to the column if the allowable stresses are 12 kpsi in steel and 1200 psi in concrete. Esteel = 29 Mpsi, Econcrete = 3.6 Mpsi. Answer A reinforced concrete column is constructed of 12 1-in-diameter steel rods. Calculate the force maximum allowable P that can be applied to the column if the allowable stresses are 12 kpsi in steel and 1200 psi in concrete. Esteel = 29 Mpsi, Econcrete = 3.6 Mpsi. Answer: 560 kips.
شكتذمسخaobckqid
Determine the shear stress in pin A shown in the figure below. The load, P is equal to 10 kN. All pins are subjected to double shear, and each has a diameter of 18 mm. Please give your answer in MPa. C A2 m 2P -2 m 30° P -2 m- B
The foundation bolt is shown in the below figure a force F = 300 N. The bolt material is wire of diameter d = 6 mm to a radius R = 10 mm in the eye and at the shank. Determine the stresses at the inner and outer surfaces at section A-A. FA B
The bar in the figure with a diameter of 25 mm and a length of 1000 mm is made of Ti6Al4V alloy. A to this bar A force of 1000 N is applied with an arm of 800 mm length from the point. this force (a) the highest stress in the bar, (b) the type of stress, (c) the location of this stress (d) calculate how many degrees the rod rotates under the effect of this force. (Module of Elasticity of Ti6Al4V alloy 105 GPa and Poisson's ratio is 0.3).
1- Calculate the stresses in members CE, DE, and DF. The cross-sectional area of each member is 1200 mm?. Indicate tension (T) or compression (C). P = 5 kN Figure P-111 6 m 8 m 8 m 8 m 6 m Fig 1 Fig 2
PLEASE ANSWER NUMBER 1.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square cross section and bar width is 15 mm. Points A, B and C are pin connections. с Square 15 mm side. 6m B 3.5m D 20KN
Mechanical design
The figure shows a bar with a point load of 22 kN applied at the free end, the other end of the bar is connected to a bracket via a bolt with a diameter of 6mm. Determine the shear stress in the bolt? O O O O 101 MPa 156 MPa Don't Know 389 MPa 603 MPa 22 kN