100NM rod-1 100N rod-2 toost took 0.75 0.50 rod-1 0. rod-2

Q: Cônnecting Ród óf å Diesel Engine cross section. It is subjected to a force of 85KN. Calculate the…

A: area of the I cross section is =2×21×6   +   5×35=427mm2=427×10-6m2

Q: 3. A 65 mm diameter solid shaft is subjected to force and torque as shown in the figure below.…

A: Given, Diameter, D=65 mm,Cross-section Area, A=π4D2A=π4652A=3318.307 mm2 Calculate the stress due to…

Q: Given dĴ 9 D = 400mm T = 300k N'm Inclined plane 0=60 d = 300mm Imax F = 1.5MN 1) Draw a square…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: An AISI 1020 steel rod 22 feet long is anchored between two rigid supports. At 90 degrees Fahrenheit…

A: For AISI 1020 steel rod, E=29000 ksi=29×106 psi and α=6.5×10-6 in/in.°F. Let Ti be the initial…

Q: (B) – Figure Q4/B show the bone has an outer rac of 15 mm and thickness 3 mm. Determine the strains…

A: Draw the diagram for the axes given in the problem. Understand that in the given figure, the shaft…

Q: The assembly consists of two rods AC and BD attached to the 100-lb uniform rigid beam AB. There is a…

A:

Q: A stepped shaft ACB having a solid circular cross sections with two different diameters and two…

A:

Q: The part shown is made from AISI 1040 CD steel and is loaded at point C with 300 N in the positive y…

A: Given : material - AISI 1040 CD diameter of bar d = 12 mmYield strength for AISI 1040 CD is 415 MPa

Q: p. A steel 150mm long, 75mm external di bronze tube of the same length, 50mm external diameter and…

A: GIVENls=150 mmlb=150 mmDs=75  mmds=50 mmDb=50 mmdb=25 mmP=50 kN=50×103NEsteel=206 GN/m2Ebronze=95…

Q: The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column…

A:

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

A:

Q: Q1 The machine element shown in the figure below is fixed supported at point B and has an applied…

A:

Q: The member shown below has a rectangular cross-section. Determine the state of stress that the…

A: Given Data: A Structural Member shown in a figure below Find: State of Stress at Point C and D

Q: Calculate the normal stress in rod BC and the displacement of point D. Also calculate the change in…

A: GivendBC=10cm=0.10mE=50GPaν=0.3P=2.5kN

Q: In the picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”.…

A: Sy=400 MPa

Q: The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to…

A: Given: To find: Resultant shear force at C in y direction Resultant shear force at C in z…

Q: (3) The cantilever bar as shown on next page is made of a brittle material. At D, F-300 lb. F-250…

A: Given data :Material of cantilever Bar= Cast iron (Brittle Material)At D: Fx= 300 lb, Fy= 250 lb,…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: Given data: P=9 kipsQ=4 kipsR=18 kipsS=21 kipsσ1=19 ksiσ2=24 ksiσ3=12 ksi Need to determine the…

Q: 1- The shaft shown in the below Fig. consists of a 75-mm diameter aluminum segment rigidly joined to…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.