The ball B has a mass of 4 kg and is attached to the end of a rod whose mass may be neglected as shown in (Figure 1). Figure M 1.5 m < 1 of 1 > B ▼ Part A If the rod is subjected to a torque M=(3+2+5t+2) N-m, where t is in seconds, determine the speed of the ball when t = 2 s. The ball has a speed v = 2 m/s when t = 0. Express your answer to three significant figures and include the appropriate units. v= ⁰ Value Submit μA 1 Provide Feedback Request Answer Units ? Next >

The ball B has a mass of 4 kg and is attached to the end of a rod whose mass may be neglected as shown in (Figure 1). Figure M 1.5 m < 1 of 1 > B ▼ Part A If the rod is subjected to a torque M=(3+2+5t+2) N-m, where t is in seconds, determine the speed of the ball when t = 2 s. The ball has a speed v = 2 m/s when t = 0. Express your answer to three significant figures and include the appropriate units. v= ⁰ Value Submit μA 1 Provide Feedback Request Answer Units ? Next >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the speed (in m/s) with which the load W rises when t = 3.6 seconds, when the system shown in the figure is used. The motor shaft rotates with an angular velocity of w=100(2+t) rad/s where t is in seconds. 50 mm D 300 mm E 30 mm W 225 mm B 40 mm M
8) A block weighing 50-kg is being pulled up the incline as shown below. The coefficient of kinetic friction between the block and the surface of the incline is 0.4. If the block is initially moving up the plane at 2m/s and at this instant (t = 0) the motor develops a tension in the cord of T = (300 + 120vt) Newtons, where t is time in seconds. Determine the velocity of the block at t = 2s. Motor V=2 m/s 30
* 5. In preliminary design studies for a sun- powered car, it is estimated that the mass of the car and driver will be m kg and the torque produced by the engine will result in a F, newton tangential force on the car. Suppose that the car starts from rest on the track at A and is subjected to a constant Ft newton tangential force. Determine the magnitude of the car's velocity and the normal component of R m END B A START l m Figure 5. force on the car when it reaches B. m = .15.. kg Fe .newton .m R = 31.25
Q2/ A force F = (7 i—10j)N acts on a particle that a displacementd = (2i + 3j)m .find the work done by the particle, and the angle between force and displacement? Q3/ A body of mass 200 kg is travelling at speed of Vi=250 m/sec .with a constant force of 100N for a displacement of 20 m. determine the final speed of the body ?
When s = 0.6 m, the spring is unstretched and the 10 kg block has a speed of 5 m/sec down the smooth plane. Determine the distance s when the block stops. See figure (4). k = 200 N/m 5 m/s F = 100 N 30/ Fig.4
Solve it correctly please. I
A motorcycle and rider have a combined mass of 350kg. The vehicle's velocity is 100 km/hr. The rider is to go up a hill incline of 10 meters. The wheels each have a mass of 20 kg and a diameter of 500mm. The wheel design consists of 6 spokes with a mass of 0.5 kg for each spoke. a. Determine the vehicle's velocity at the top of the hill, assuming it was a rolling vehicle with engine being turned off. a. Indicate the vehicle's velocity at each meter through the climb. b. Explain the transfer energy and how this affects the behaviour of the system. At another point in its journey, the motorcycle and rider travel at 80 km/h around a left-hand bend of radius 30m. Calculate: a) The angular velocity of each wheel. b) The moment of inertia of each wheel. c) The angular momentum of the wheel prior to entering the bend. d) The magnitude of the gyroscopic torque produced on the bike as the rider is driving around the bend. What is the effect and why is it important to calculate the gyroscopic…
The double pulley shown in the figure is formed by two wheels that are coupled to each other. The complete pulley (formed by the two wheels) has a mass of 15 kg and a turning radius of 110mm. Block A has a mass of 40 kg. If a force of 2 kN is applied to the tied rope of the inner pulley wheel, determine the speed of block A after 3 seconds. At the beginning, the whole system was at rest. Disregard the mass of the string and consider that the moment of inertia (kg.m²) of the complete pulley is given by IP = mko²where m is the mass of the pulley and Ko is the radiusspinning
The amusement park ride consists of a 200-kg car and passenger that are traveling at 4.6 m/s along a circular path having a radius of 8 m. At t = 0, the cable OA is pulled in toward O at 0.5 m/s. (Figure 1) Figure Part A Determine the speed of the car when t = 4 s. Express your answer to three significant figures and include the appropriate units. V2 = Submit Part B O μA U1-2 = Value Request Answer Determine the work done to pull in the cable. Express your answer to three significant figures and include the appropriate units. ΜΑ Units Value ? Units ?
At the start, Box A has a speed of 3 m/s upward the inclined plane with a kinetic friction equal to 0.15. Determine the speed of Box B at t = 6 seconds.
The 52 kg block is hoisted up the incline using the cable and motor arrangement shown. (Figure 1) Figure 2 m/s Part A The coefficient of kinetic friction between the block and the surface is = 0.4. If the block is initially moving up the plane at v0 = 2 m/s, and at this instant (t = 0) the motor develops a tension in the cord of T = (300+120√t) N, where t is in seconds, determine the velocity of the block when t = 4 s. Express your answer to three significant figures and include the appropriate units. v2 = Submit Value Provide Feedback A Request Answer → Ò Units ? Next >
Dynamics