The assembly shown consists of two wooden members joined by metal plates. steel and four steel screws. The diameter of the screws is “d”. Determine: a) The crushing force between the wood and the screws. b) The shear stress in the wood

Q: 9.9 A No. 32 (metric designation) reinforcing bar for concrete has a diameter of 32 mm. The bar is…

A:

Q: 1.7 in 2.5 in 2.7 in T 0.755 in Three wood boards, each 4.3 in. wide, are joined by the…

A:

Q: The wooden members A and B are to be joined by plywood splice plates that will be fully glued on the…

A: Given data P = 35.9 KN  Width (W) = 119 mm Length (L) = 288 mm  x = 11m

Q: The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter…

A:

Q: If the force P reached 10 kN, the wooden specimen shown failed in bearing along a surface. Calculate…

A:

Q: The wood members A and B are to be joined by plywood splice plates that will be fully glued on the…

A:

Q: 2. Determine the minimum dimension h to the nearest mm of the beam's cross section to safely support…

A:

Q: 75 /2 100 mm

A:

Q: shear strength value is in wood parallel to the grain O a. medium O b. Maximun O C. least O d.…

A:

Q: Answer this using method of joints. Show your clear, detailed, and whole solution. Don’t mind the…

A:

Q: A subcontractor must join two wooden planks to lengthen a tension member (see Figure 5). It does…

A: E = 140MPa α = 13.5x10-5/°C σw = 30MPaσs = 30 MPa Bolt shear = τb = 70MPa Change in temperature = ∆T…

Q: Problem 4: Find the design moment strength for the following section: f'c = 7000 psi Es = 29,000 ksi…

A: Stress strain curve reinforcing steel,

Q: GIVEN; Steel / wood composite beam with cross-section shown Mmax = 1.5 x 10° in-lb Estel = 30 x 10º…

A: Composite beam: The combination of one or more material used in the manufacturing throughout the…

Q: The two pieces of wood, 1.78in. by 4.75 in., are glued together along the 40ᴼjoint. Determine the…

A: From the given data  Area A = 1.78 * 4.75 = 8.455 in²  Max shear stress in the glue  limited to 234…

Q: 3 kN 1.5 kN 2 kN 2 m 2 m + 2 m 2 m --1.5 m-|-1.5 m--1.5 m-| D A В

A:

Q: med joint by the g. Determine t

A: Dimension of block = 2.5in.*2.5in. Sliding angle = 55° Length of steel key = 2.5in.  Working Bearing…

Q: The two wooden boards are connected by a 0.9 in. diameter bolt. Washers are installed under the head…

A:

Q: two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm.…

A: Find modular ratio:n=EwEs=40200=15so,Reduced width of wood =1505=30mmFInd…

Q: 1 Plastic State: For the following section determine the maximum bending moment the section can take…

A: Given: The strength of the concrete is 45 MPa. The strength of the steel is 400 MPa.

Q: 5. Given : Allowable bending stress of 12.5 MPa Allowable shearing stress of 0.45 Mpa Elasticity of…

A:

Q: A laminated beam is composed of four planks, each 6 in. by 2 in., glued together to form an outside…

A: Given Data:Size of planks = 6in×2inAllowable shear stressglue = 90 psiThe allowable shear stress in…

Q: Example: Calculate the strength of the single lap joint. The plates are made of 1"x4" wooden blocks…

A:

Q: Given a 10"X16" reinforced concrete beam section as shown. The main reinforcing rebars consist of…

A: f'c=3000 psify=60 ksiTo determine:Theoretical nominal bending moment

Q: A beam is fabricated by gluing four dimension lumber boards, each 40 mm wide and 80 mm deep, to a 30…

A: Given data,  Allowable bending stress = 5.7 MPa Allowable shear stress in plywood = 545 kPa…

Q: 4. The two pieces of wood, 2 in. by 4 in., are glued together along the 40⁰ joint as shown in figure…

A: Area of wood pieces, AngleTo find:           (A) Maximum load for wood strength of .           (B)…

Q: Derve the maximum steel ratio and the recommended steel ratio. show solution and explanation.

A: Draw strain diagram as shown belowUsing linearity concept we can write d* - c* = *cd*  = *c + c*d*…

Q: he T-beam has the following properties:  flange thickness = 110 mm flange width = 700 mm web…

A:

Q: Determine the average shear stress developed in the wood fibers that are oriented along section a-a…

A:

Q: Two wooden members of (25*b) * (60*b)-mm? uniform rectangular cross section are joined by the simple…

A: Given, Cross section area = 175 mm x 420 mm Load P = 12 kN Ultimate tensile strength = 4 MPa…

Q: he repair and rehabilit amaged or spalled co one emovina the by ro

A:

Q: Determine the average normal stress developed in the wood fibers that are oriented along section a-a…

A:

Q: mm web height = 350 mm

A:

Q: P 2 m W = X N %3D F1m- 4 = 0,3 - 1m-| Determine the normal force between the crate and the surface…

A: To find the normal force (N) and force (P)-

Q: The working stresses for the manufactured wood beam are 10 MPa in bending and 1.4 MPa in shear.…

A:

Q: d. stress in the steel bars; e. deformation of the concrete post

A: Given  Load Cross sectional area  Modulus of Elasticity  Required  d. stress in the steel bars;e.…

Q: The steel channel is used to reinforce the wood beam. Determine the maximum stress in the steel and…

A:

Q: Two wood boards, each 18 mm thick, are joined by the glued finger joint shown. The finger joint will…

A: Determine the shortest allowable length d of the cuts?

Q: The two pieces of wood, 2.94in. by 4.76 in., are glued together along the 48ᴼjoint. Determine the…

A: Determine the maximum safe axial load P (in lb) that can be applied

Q: L L T The wooden bar consists of two segments, each of length L. One segment has a square cross…

A:

Q: Dicuss one way shear

A: The tangential force acting on the surface is known as shear force.

Q: 5. The piece of P wood, 100 mm by 100 mm in cross section, contains a glued joint inclined at the…

A: We have to determine the value of largest allowable axial force P as per the given data in the…