The arm is rotating at a rate of 0 = 4rad/s when ôÔn = 3rad/s² and 0 = 180°. Determine theforce it must exert on the 0.5-kg smooth cylinder if it is confined to move along the slottedpath. Motion occurs in the horizontal plane.= 4 rad/s, ö = 3 rad/s²0 = 180°: (금) mr =

Answered: Image /qna-images/answer/87a1c215-f2a8-4102-80f7-c5d88101890a.jpg

Answered: The arm is rotating at a rate of 0 =…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
The spring-mounted 0.62-kg collar A oscillates along the horizontal rod, which is rotating at the constant angular rate ở = 6.3 rad/s. At a certain instant, ris increasing at the rate of 630 mm/s. If the coefficient of kinetic friction between the collar and the rod is 0.46, calculate the friction force F exerted by the rod on the collar at this instant. Vertical Answer: F = i N
The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. Find the velocity of the block after it moves 20m starting from rest. the answer must be 3 decimal places.
1. Determine what the acceleration of the cable into winch A must be for the tension in the cable to be 200 lb. Crate C has a mass of 10 slugs. The cable acceleration into winch B is shown. B ap=2 ft/s2 ap = 3 ft/s² (o). A
The particle of mass m = 2.5 kg is attached to the light rigid rod of length L = 1.27 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity = w = 3.2 rad/s. Determine the force T in the rod when 0 = 36°. The force Tis positive if in tension, negative if in compression. L Ꮎ m
The ball has a mass of 0.5 kg and is confined to move along the smooth horizontal slot due to the rotation of the arm OA. Determine the force of the rod on the ball and the normal force of the slot on the ball when 0= 30°. The r= (6t?) is a function with respect to time. Determine r, r', and r" at t=3 s. 0'= 2 rad/s and 0"= 3 rad/s2. A ở = 2 rad/s 0.5 m
= Q1: The 1.5-kg ball is given an initial velocity VA 2.5 in the vertical plane at position A, where the two horizontal attached springs are unstretched. The ball follows the dashed path shown and crosses point B, which is 12 cm. directly below A. Calculate the velocity of the ball at B. Each spring has a stiffness of k = 1 ª N m VA 30 cm 30 cm 12 cm A UB B Fig. 1
A 100 pound pipe is at rest vertically, when the cable is connected to B at the force of P=50 pounds. Find the pipes angular velocity and acceleration at A. Please include FBD is necessary. Thank you. 4 ft A 3 ft P = 50 lb В 3 ft
Q/ For the mass - spring shown, determine the magnitude of the mass m 50 mm. -3 kg www. 12 mm mass v-4 m/s
The spring is not stretched or compressed when “s=0.8m" and the 11 kg block which is subjected to a force of 105 N has a speed of 5.5 m/s down the smooth plane. Using "THE PRINCIPLE OF WORK AND ENERGY", find the distance "s" when the block STOPS. k = 200 N/m 5 m/s F = 100 N 30°
The helical path is wound around the circular cylinder with radiusR . The step h= 2*pi*R. The object A is sliding through the path guide under gravity (acting in the negative zdirection). There is no air resistance 1)Draw the force diagrams in (theta ,Z ) plane (tangent to the cylinder) and in( r,theta ) plane. 2) If the initial speed is 0, find the speed after 3 full circles. Given: R, g, m, u.[Hint: Use the work-energy principle.]
M = A frisbee is thrown such that its final angular velocity is w = 9 after being in flight for t = 2 s. As it rad S flies, the wind applies a constant moment, causing the frisbee to rotate faster. If the frisbee was initially at rest, determine the moment of the wind and the work done by said moment. Assume the frisbee can be modelled as a disk with mass m = = 0.15 kg and that it rotates about its center of gravity G. The frisbee has a radius of r = 0.12 m. UM = N.m r J G M

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

The arm is rotating at a rate of 0 = 4rad/s when ôÔn = 3rad/s² and 0 = 180°. Determine the force it must exert on the 0.5-kg smooth cylinder if it is confined to move along the slotted path. Motion occurs in the horizontal plane. = 4 rad/s, ö = 3 rad/s² 0 = 180° : (금) m r =