If the 50-kg load A is hoisted by motor M so that the load has a constant velocity of 1.5 m/s, determine the force (T) of the cable connected directly on the block.

Q: R13-2. The motor M pulls in its attached rope with an acceleration q = 6 m/s². Determine the towing…

A: An external push or the pull act on the object due to which the state of the object can be changed…

Q: Determine the speed v which the 525-kg four-man bobsled must have in order to negotiate the turn…

A: To Find :  The normal reaction force and speed v . Given :  The mass of bobsled is M=525 kg distance…

Q: The super-container vessel has a total mass displacement of 23000 long tons. This vessel towed by a…

A: The velocity is v=2 knot=2×0.5144=1.0288 m/s The horizontal component of force is…

Q: 2. The roller coaster car has a mass of 700 kg, including its passenger. If it is released from rest…

A: Consider that the height at point A is taken as the datum that is all the heights will be measured…

Q: The 1.1-kg slider is released from rest in position A and slides without friction along the…

A: Step 1:Mass is 1.1kgSpring constant is 34kmN​Step 2:We know that to establish datum at point…

Q: The 7-kg smooth cylinder is supported by the spring having a stiffness of kab = 120 N/m. Determine…

A:

Q: The 10-Mg barge B supports a 2-Mg automobile A. If someone drives the automobile to the other side…

A:

Q: The 50-lb load is hoisted by the pulley system and motor M. If the motor exerts a constant force of…

A:

Q: h k to с www

A:

Q: Determine the speed v which the 670-kg four-man bobsled must have in order to negotiate the turn…

A: Mass =670kg, Find, V and N

Q: The steel ingot has a mass of 1800 kg. It travels along the conveyor at a speed v=0.5m/s when it…

A: GivenM=1800kgV=0.5m/sKA=5kN/m=5000N/mx=0.3m

Q: 3. The smooth 160-lb pipe has a length of 20 ft and a negligible diameter. It is carried on a truck…

A: Find the acceleration and reactions at point B

Q: 14-34. The spring bumper is used to arrest the motion of the 4-lb block, which is sliding toward it…

A: Given Data: The weight of the block is w = 4 lb. The velocity of the block is v = 9 ft/s. The…

Q: F13-9. A pilot weighs 150 lb and is traveling at a constant speed of 120 ft/s. Determine the normal…

A:

Q: The 10-lb block has a speed of 4 ft/s when the force of F= (8t^2) lbf is applied. Determine the…

A: Free body diagram of the block is showing below,Here m is mass of block, a is acceleration of block,…

Q: 14-1. The 20-kg crate is subjected to a force having a constant direction and a magnitude F = 100 N.…

A: Given data: Mass of the crate, m = 20 kg. The magnitude of force F, F = 100 N. Speed of crate when…

Q: y y- 4.5 - h ft k lblft B I ft The 8-lb collar has a speed of 9 ft. s at A. The attached spring has…

A:

Q: The 925-kg motorized unit A is designed to raise and lower the 615-kg bucket B of concrete.…

A:

Q: The 50-1b block rests on the smooth surface. A force F = (40+s) Ib, which s isin ft, acts on the…

A:

Q: F = 15 N If the rod of negligible mass is subjected to a couple moment of M=24t2 N;M where t is the…

A:

Q: Determine the speed v which the 690-kg four-man bobsled must have in order to negotiate the turn…

A: Given data- Mass = 690 kg Find the speed and normal force on the bobsled.

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.