The area to be measured for painting distemper for an internal surface of a plastered 230 mm thick brick wall having dimension of 3000 mm length and 3200 mm height and having a glazed louvered ventilator of size 600 mm x 400 mm in the wall is A 9.60 sq.m B) 9.36 sq.m C 9.84 sq.m D) 9.12 sq.m

The area to be measured for painting distemper for an internal surface of a plastered 230 mm thick brick wall having dimension of 3000 mm length and 3200 mm height and having a glazed louvered ventilator of size 600 mm x 400 mm in the wall is A 9.60 sq.m B) 9.36 sq.m C 9.84 sq.m D) 9.12 sq.m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: -2 ft 10 kip 4 in. -1.5 ft--- 4 in. B B 6 in. 4 kip - 0.5 ft 13 in. 2 ft- - Change the magnitude of…

A: Given:- Cross section of the beam is To find:- Maximum in plane shear stress at point A Principal…

Q: Problem #3 12 kN/m El = constant E= 70 GPa I= 210x10 mm* Required: 6max OA 0B %3D C A. 3m 4m

A: Moment equation:Mx=-12x22+12x-322Mx=-6x2+6x-32so, using double…

Q: A steel building has plan dimensions of 50m x 50m and it is 120 m tall. It is provided with brick…

A: According to given data Plan dimension= 50 x 50 in meters and Height is 120m

Q: A retaining wall with measurements 30m x 12m x 6m was constructed with bricks of dimensions 8cm x…

A: Given - Dimension 0f wall = 30m×12m×6m Dimension 0f brick = 8cm×6cm×6cm…

Q: the level of water at A to maintain a constant depth of 11 ft. If the 50(10³) lb, determine the…

Q: 900N/m 1.1m 1.3m + 750N/m 1.1m

A: Loading and dimensions are given There will be reactions and moments at 2 fixed supports Form…

Q: Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses R1 and R2,…

A: Answer To derive the capillary rise formula consider the forces acting on the water due to surface…

Q: Determine the yof the shaded area. L= 2.9m L -y = x³

Q: Activity 1. A 25-kg ladder, 4 m long, rests on a rough floor and against a vertical wall. The ladder…

Q: 8. Resultant force on a 1 mx 1 m gate immersed vertically at a depth of 2 m below the free water…

Q: A vertical gate shown in Figure B has its one face completely in contact with water while the other…

A: The below figure is shown in question;To determine:-The location of the center of pressure, reckoned…

Q: E = 22.324 x 10° psi beol = 1.00 in. deol = 0.066 in. Weight of each floor 4.13 lb 6.000 Column…

A: f = √E/b*d*w = √22.324 x 10⁶/1x 0.066x4.16 = 48 khz .

Q: A storm drainage canal drains water (S = 1.0) out into the sea (S=D1.03).

A: Draw the free body diagram as below. Consider the left hand side portion Determine the…

Q: A computer room located on the second floor of a five-storey office building is 10m X 7m. The…

A: Answer We are given exterior wall dimension 3.5m x 10 m steel back with 10 mm insulating board 75…

Q: 9. Calcsheet appears shear moment deflection all previous 1.Calculate the size of the net volume if…

Q: A triangular gate with a base width of 2.5 m and a height of 2m lies in a vertical plane. The top…

Q: Freezing techniques (ground freezing or soil freezing) can be appropriate for stabilizing or…

A: Freezing is a method of soil stabilizing also known as ground freezing. It help in improving the…

Q: PROBLEM 2: The 280-kg, 6m-wide rectangular gate shown is hinged at B and leans against the floor at…

Q: Determine the volume of 50-mm plain concrete bedding.

A: Following are the given information. Thickness of plain concrete bedding =50 mm=0.050 m Length of…

Q: Yelocity orofile inside boundar y layer is given a5. sin f Find the value of 8

A: Following is the given velocity profile:

Q: A projectile, launched at A with an initial velocity of 100 m/s at the angle theta = 71 degrees,…

A: Given Initial velocity= 100 m/s Angle = 71 degree

Q: 1. A steel tape have a standardized length of 30.00m, with 5 kg tension, at 30 °C, and supported…

Q: Geotechnical engineering ( Civil Engineering) X = 6.9 Calculate lateral pressure at 2, 4, and 6m…

A: Given data: Surcharge=10 kn/m2ϕ=30°γ=15 kN/m3It is asked to find lateral pressure at 2, 4 and 6m…

Q: If the velocity through rack at max design DWF is 0.58 m/s, and the velocity through rack at peak…

A: Given:- The velocity through the rack at max design dry weather flow (DWF) = 0.58 m/s The velocity…

Q: Water is ejected from the water nozzle with a speed vo = 50.5 ft/sec. For what value of the angle e…

Q: Q.29 In SDOF system, the frequency ratio is 0.50 and damping ratio is 10%. The dynamic magnificator…

A: In SDOF SYSTEM, frequency ratio =0.5 Damping ratio = 10%

Q: Question#4\\ As shown in figure 3, when the flow rate at pipe (No.4) equals (0.6 m/sec). Calculate…

A: Solution:-Given Data,Flow rate in pipe 4=0.6 m3/secThe diameter of pipes are ,D1=450mm=0.45…

Q: A uniform 12.0 kq door with dimensions 75cm x 200 cm iS Pivoted at hinges' 25 cm from the top and…

A: Given: The mass of the door is 12.0 kg. The dimension of the door is 75 cm x 200 cm. The distance of…

Q: Problem 10.7 The shaded area shown in (Eigure 1) is bounded by a, y axes and the curve y²-2.89-0.52…

A: Given equation ;can be written as ;Now ;Substituting value of x we get ;

Q: Calculate the overall sound index for the wall with the given values below: B m² 25.0 W m² 3.0 A…

A: Given data, Area of brick wall (Aw) = 25 m2 Area of opening window (AA) = 3 m2 Sound reduction…

Q: hen đó we use the gradient wall

A: Solution: The Gradient wall foundation is used to spread the weight of the load bearing wall across…

Q: 2.53 Calculate the maximum capillary rise of water between two vertical glass plates spaced 1 mm…

Q: In an experiment with right-angled V-notch the discharge is calculated to be 0.05 m³/min. Taking…

A: Given data :Discharge (Q) = 0.05 m³/min Coefficient of Discharge (Cd) = 0.63 Actual Discharge…

Q: 3m 2m li.5m 2m Ti.5m

Q: 9.11 As shown, a curtain wall is constructed of brick masonry (a bottom of the masonry wall bears on…

A: The thermal stress developed in the curtain wall is calculated using: σ=αE∆T - - - - 1where…

Q: Consider the building in Figure P2.22, which has awidth into the page of 35 ft. Maximum inundation…

A: Force is the measuring value of the response to such a load or displacement from a template or to…

Q: Design the reinforced concrete wall shown if f= 4000 psi and f, = 60,000 psi. V = 300k

Q: A line was determined to be 354.7654 m when measured with a 50-m steel tape supported throughout its…

Concept explainers

Finishing Operations

Finishing operations are the processes that are applied to the workpiece at the end of a manufacturing process, and after completing all other relevant operations that bring the product to its required dimensions. Finishing operations involve polishing, reducing the surface roughness, eliminating wrinkling, and grinding to enhance the surface texture and provide a better surface finish to the workpiece surface.

Question

The area to be measured for painting
distemper for an internal surface of a
plastered 230 mm thick brick wall having
dimension of 3000 mm length and 3200
mm height and having a glazed louvered
ventilator of size 600 mm x 400 mm in
the wall is
A) 9.60 sq.m
B) 9.36 sq.m
с 9.84 sq.m
D) 9.12 sq.m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A furnace wall is composed of three layers, 25cm firebrick (k=1.65W/m·K), followed by 20 cm of kaolin insulating brick(k=0.078W/m·K), and finally 15 cm of masonry brick(k=1.25W/m·K). The temperature of the inner wall surface is 935°C and outside surface is at 35 °C. Assume that surface area is 1m². (1)What is the energy transfer rate q(W)? (2) What are the temperatures at the two contacting surfaces?
A 100‐ft steel tape standardized at 68° F and supported under a tension of 20 lb, was found to be 100.012ft long. The tape had a cross‐sectional area of 0.0078 in^2 and a weight of 0.0266lb/ft. The ground is on a smooth level grade, thus the tape will be fully supported. Assume a temperature increase of 19°F. Assume thermal coefficient equal to 0.00000645/°F Determine total correction (due to incorrect length and temperature) to be applied to lay out a horizontal distance of 175 ft.
A line was determined to be 354.7654 m when measured with a 50-m steel tape supported throughoutits length under a pull of 4,567 kg at a mean temperature of35.495'C. Tape used is of standardlength at 20.0°C under a pull of 5.435 kg. Cross-sectional area of the tape is 0.0367cm2.Coefficient of thermal expansion is 0.00001160/C. Modulus of elasticity of tape is 2x106 kg/cm2.Determine the corrected length of the line.
onsider the shaded area shown in (Figure 1). Suppose that aaa = 140 mmmm , bbb = 200 mmmm , and rrr = 75 mmmm .
I need the answer as soon as possible
Hi kindly answer the problem attached image below. Thank you!ASAP.
A 2-ft-diameter hemispherical plexiglass "bubble" is to be used as a special window on the side of an above-ground swimming pool. The window is to be bolted onto the vertical wall of the pool and faces outward, covering a 2-ft-diameter opening in the wall. The center of the opening is 4.1 ft below the surface. Determine the (a) horizontal and (b) vertical components of the force of the water on the hemisphere. (a) FH = (b) Fy= lb (outward) (down on bubble)
Situation:A 50m steel tape was standardized and supported throughout its whole length and found to be 0.00329m longer at an observed temperature of 41.6 degrees C and a pull of 12 kilos. This tape was used to measure a line that was found to be 683.21m at average temperature of 49 .8 degrees C at the same pull. Coefficient of the thermal expansion in 0.000016m/m degrees C. -DETERMINE THE STANDARD TEMPERATUREa. 35.93 c. 50.76b. 44.63 d. 68.25-WHAT IS THE CORRECT LENGTH OF THE LINE?a. 633.88 c. 638.23b. 663.28 d. 683.32
Determine ϕMn for the cross section that has a rectangular duct cast in it, as shown. Use f′c=3000 psi, fy=75,000 psi, 1-in. clear space between bar layers, 1.5 in. cover, and eight No. 7 bars, as shown.