The Air on 1 ATM on T. = 250 K And the free flow rate is 30 meters It flows across a diameter cylinder 2,5 cm The cylinder 'surface is guarded on temperature 350 k, count : *) The rate of heat transfer is 1 meter long Cylinder >

The Air on 1 ATM on T. = 250 K And the free flow rate is 30 meters It flows across a diameter cylinder 2,5 cm The cylinder 'surface is guarded on temperature 350 k, count : *) The rate of heat transfer is 1 meter long Cylinder >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please show all work clearly
Please solve accurate...
Please show all work
Q4: Three pipes A, B and C, are interconnected as shown in figure (4). The pipes characteristics are as follows. L (m) f 600 0.02 B 480 0.032 C 1200 0.042 Find the flow rate at which water will flows in each pipe, also find the pressure at point (P). Pipe EL. 60m Water B Figure (4) D (cm) 15 10 20 P EL.36m C EL.15m water
Hi please show calculations or diagrams if required thank you
Q2: The temperature of a gas steam is to be measured by a thermocouple. Determine the time it take: p =8500 kg/m _and C-320 J/kg to register 99% of the initial AT . For junction k=35 W/m.°C Ans : 38.5 sec Gas Junction D. h. T. 11111
Please solve and write out equations used. Thanks
A hot small copper ball [c in kJ/kg.°C, k in W/m.°C] is suddenly placed in water maintained at 100 °C. The convection heat transfer coefficient is h in W/m². ºC. Derive equation to calculate the time required to reduce ball to temperature T.
10B.4. Heat conduction in an annulus (Fig. 10B.4). (a) Heat is flowing through an annular wall of inside radius and outside radius ₁. The thermal conductivity varies linearly with temperature from ko at To to k₁ at T₁. Develop an ex- pression for the heat flow through the wall. (b) Show how the expression in (a) can be simplified when (r₁-ro)/ro is very small. Interpret the result physically. Answer: (a) Q = 2πL(T₁- To T₁ T₁) ›(ko + k) (in 7.) *'; 2 "'; (b) Q = 2mr_L (ko + ki ) ( 7 2 Problems 323 Fig. 10B.4. Temperature profile in an annular wall.
Newtons laws of cooling proposes that the rate of change of temperature is proportional to the temperature difference to the ambient (room) temperature. And can be modelled using the equation: dT/dt = -k (T-Ta)It can also be written as dT/T-Ta = -k dtWhere:T = Temperature of materialTa = Ambient (room) temperaturek = A cooling constanta) integrate both sides of the equation and show that the temperature difference is given by:(T-Ta) = CoE^-kt(Co is a constant for this problem)B) calculate Co if the initial temperature is 70 degrees C and Ta = 20 degrees C?
I need the answer as soon as possible
36 -S 42 2. Metal castings can sometimes develop a gap between the casting and mold as the molten metal hardens. The result can be a substantially altered cooling process. Set up a simple heat-transfer model that would let you look at the effect of the gap on the cooling process. Assume the casting and mold are square in shape, with an air gap of thickness das shown in the figure. The mold sits in some ambient room temperature. State clearly all assumptions and develop a corresponding model of the heat transfer problem. Assuming that the casting is aluminum, the mold is diatomaceous earth and the gap is filled with air, see if you can arrive at and summarize some insight into the effect of the gap and its size on the heat transfer process.