The air conditioner (a kind of vapour-compression refrigerator) in a 1500-cc car, which works on a pseudo-ideal reversed Rankine cycle, uses R-134a, the isentropic rotary-com- pressor of which consumes power at a rate of 1.5 kJ/s bringing the R-134a from 2.017 bar to 12 bar by compression. The cold space is a heat exchanger (using a hamster wheel as a blower) that cools atmospheric air from the outside temperature of 303 K down to 283 K and blows it into the car. Assume the start of compression process is state point 1. The refrigerant at evaporator exit is dry saturated vapour and saturated liquid at the condenser exit. Draw the schematic and T-s diagrams for the cycle. (a) What is the mass flow rate of the R-134a (mg-134a )? (b) What is the low-temperature heat transfer rate? (c) How much is the mass flow rate of air ( mi) at 283 K? For air, take cp = 1.004 kJ/(kg·K). %3D

The air conditioner (a kind of vapour-compression refrigerator) in a 1500-cc car, which works on a pseudo-ideal reversed Rankine cycle, uses R-134a, the isentropic rotary-com- pressor of which consumes power at a rate of 1.5 kJ/s bringing the R-134a from 2.017 bar to 12 bar by compression. The cold space is a heat exchanger (using a hamster wheel as a blower) that cools atmospheric air from the outside temperature of 303 K down to 283 K and blows it into the car. Assume the start of compression process is state point 1. The refrigerant at evaporator exit is dry saturated vapour and saturated liquid at the condenser exit. Draw the schematic and T-s diagrams for the cycle. (a) What is the mass flow rate of the R-134a (mg-134a )? (b) What is the low-temperature heat transfer rate? (c) How much is the mass flow rate of air ( mi) at 283 K? For air, take cp = 1.004 kJ/(kg·K). %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If the voltage Vs = 800 mV, then the current flowing in the primary winding Ip, is: 1:8 -j202 Select one: a. Ip =40<0° mA O b. Ip =320<-90° mA O c. Ip = 0.320<90° A %3D O d. None of these ll
I need the answer as soon as possible
Write down the differential equations describing the loop currents of the given circuit. Assume clockwise rotation and i passes through the voltage source. R1 2 Ohms L1 C1 0.5F 0.3H Vs V R3 6 Ohms R2 10 Ohms C2 0.25F
Verify the following property of the twiddle factor:
A 15µF capacitor and a 470 ohm resistor are connected in series with a function generator. The supply voltage is 50V RMS 40Hz. Find the reactive power for this circuit.
1) The switch in the ciruit, shown in belou has been in Posikon "a" for a long hime. At t=0, the switch moves instantancously ho positron "b". Find volt) for t70 960n 1602 o.SmH 28V 12-5 nF 20v Volt)
The power consumed by a coil is 300 W when connected to a 30 V dc source and 108 W when connected to a 30 V ac source. The reactance of the coil is?
DRAW THE CIRCUIT AND KVL LOOPS ANALYSIS .
Q3) Answer one of the following questions a. For the following circuit below, find the RMS load voltage for (a=0, a=30, a=60, and a=90). 30 60 90 VLoad rms ILoad 20 Vs= rms Gate Drive R+L V Loud fs=50 Hz
An impulse turbine is used for a. Low head of water b. High head of water c. Medium head of water d. High discharge
An emergency power supply is required to provide a three-phase sinusoi- dal voltage source of 208 V (L-L) at a frequency of 400 Hz. The power is to be obtained from a battery consisting of cells in series, each cell hav- ing an internal voltage of 2.2 V and an internal resistance of 0.006 m. The load on the three-phase, 400-Hz system requires a fundamental fre- quency apparent power of 7.2 kVA at 0.9 power factor lagging. The in- ductance of the load is such that harmonic currents are negligible. How many cells should be connected in series to provide the required output? The switches may be regarded as ideal.
An impedance oil takes 144 watts at a lagging factor of 0.6. What values of capacitance and resistance should be connected in series with the coil if the power input to the latter is to remain unchanged and the overall circuit is to be unity? The circuit is energized by a Voltage of 120 v and frequency is 60Hz