Answered: The 7m simple beam below carries a…

The 7m simple beam below carries a uniform load of 8KN/m. If EI is 13333.33KNm2 of the beam in figure 03 below, the maximum deflection is nearest to

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.7P

See similar textbooks

Related questions

Q: 10 kN/m 25 kN m A E B IC 1 m 1m 3 m 2 m Fig. P4.31 DEFLECTIONS IN BEAMS USING DOUBLE INTEGRATION…

Q: Determine the deflection at the midspan of the beam shown using conjugate beam method

A: Solution:

Q: 180 kN 15 kN/m B D -5 m- -5 m- -4 m- El = constant E = 70 GPa I = 2,340 (106) mmª %3D

Q: Determine the location and magnitude of the maximum deflection for the beam shown below using double…

Q: Problem 13: Determine the horizontal deflection at point D for the frame as shown in figure by…

A: Given : E = 2 X 105 N/mm2 I = 8 X 108 This is a problem of structure where we are asked to…

Q: Nő. 4 For the frame shown below, compute the vertical deflection at point B.

A: Solution: Considering the diagram; Taking moment about point…

Q: beam of length 6m is supported at its ends and carries UDL 0f intensity (25+33 kN/m) as shown in…

A: Solution; Given data; The length of beam AB is given as 6 m. But the sum of AB, CD, DB is 8 m. So,…

Q: Use Conjugate Beam Method

Q: A uniform beam of length L embedded at its left end and free at right end and · 00571 carries a…

Q: please determine deflection at point C by assuming the stiffness (E,I) is constant (use conjugate…

A: ###Deflection at C of Given beam using Conjugate Beam method####

Q: 1. Determine the beam For the beams and loading shown below, EI is constant deflection at point C.…

Q: Simply supported beam A carries a point load at its midspan. Another identical beam B carries the…

Q: Calculate the deflection at free end on the given beam shown in the figure using area moment method.…

A: find deflection at free end find reaction 1st draw M/EI diagram Apply Mohrs 2nd theorem

Q: A concentrated load, P is appied at the center of a simply supported beam with length, l. What is…

A: Please refer the attached image for complete solution. THANKYOU !

Q: 1: Both portions of the rod ABC are made of an aluminum for which E= 70 GPa. Knowing that the…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

The 7m simple beam below carries a uniform load of 8KN/m. If EI is 13333.33KNm2 of the beam in figure 03 below, the maximum deflection is nearest to

8 KN/m
7m
Figure 03: Simple Beam with Uniform Load

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
Same as Problem 5.10-2, except that lateral support is provided only at the ends and at the concentrated load.
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.
Use A992 steel and select a W14 shape for an axially loaded column to meet the following specifications: The length is 22 feet, both ends are pinned, and there is bracing in the weak direction at a point 10 feet from the top. The service dead load is 142 kips, and the service live load is 356 hips. a. Use LRFD. b. Use ASD.