The 52-kg cylinder is suspended from a clamping collar at C which can be positioned at any horizontal position x between the fixedsupports at A and B. The cable is 11 m in length. Determine and plot the tensions in cable segments AC and BC as a function of x overthe interval 0 < x < 10. Do your plot on a separate piece of paper. Then answer the questions to check your results.10 mAB52 kgQuestions:(a) If x= 3.3 m, the tension in cable AC isiN(b) If x = 8.7 m, the tension in cable BC is iCaZ ZN

Answered: Image /qna-images/answer/5a1b336a-1729-4a7b-afce-ad7ce114119e.jpg

Answered: The 52-kg cylinder is suspended from a…

Similar questions

Chapter 12, Problem 028 GO In the figure, suppose the length L of the uniform bar is 3.1 m and its weight is 240 N. Also, let the block's weight W = 270 N and the angle e = 41°. The wire can withstand a maximum tension of 420 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? Com (a) Number Units (b) Number Units (c) Number Units
Suppose three forces with magnitudes of 220 N, 270 N, and 200 N are placed in equilibrium. If the 200 N force acts in the +y-direction,what are the two configurations in the xy-plane that the remaining forces may have? Give numerical values for the angles and show your results on a sketch.
A 1204-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end A 1515-N crate hangs from the far end of the beam. Find the magnitude of the tension in the wire. The angle theta (9) is 29 degrees and the angle phi () is 53 degrees. The length of the beamis L Вeam ROUND OFF FINAL ANSWER TO THE NEAREST WHOLE NUMBER. INPUT THE SYMBOL OF THE UNIT. NO SPACE BETWEEN THE NUMBER AND THE UNIT.
Needs Complete typed solution with 100 % accuracy.
Determine two force members first. Two blocks are each pin connected to a massless horizontal link. Determine the largest P before motion cocurs. Use 0.35 and 0.3 for the friction coefficients. 4.5 kg 3 kg B 30°
A beam of length 11 m is supported as shown below. There is a pin in the bottom end of the beam and a mass hanging from the top end of the beam. If the mass of the beam is mb =264 kg, the hanging block has a mass of m1 =81.8 kg, theta = 50.1 degrees, and phi = 35.1 degrees, what is magnitude of the tension in the wire attaching the beam to the ground?
A uniform ladder of length L and weight w is leaning against a vertical wall. The coefficient of static friction between the ladder and the floor is the same as that between the ladder and the wall. If this coefficient of static friction is u, = 0.385, determine the smallest angle the ladder can make with the floor without slipping. 52.4 Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error.°
In the figure, a uniform plank, with a length L and a weight of W, rests on the ground and against a frictionless roller at the top of a wall of height h. The plank remains in equilibrium for any value of 000 or more, but slips if = 000. Find the coefficient of static friction between the plank and the ground. NOTE: Give your answer in terms of the variables given. flg = L 0 Roller h
Consider two geometrically identical marbles stacked in a container as shown. The radius of each of the marbles is R. while the width of the container is 2.9R. The marble at the top has a weight 0.78 N while the weight of the lower marble has a weight of 0.82 N. What is the magnitude of the normal force at point B? Express your answer in Newtons and with two decimal places. C А В
Hand written and clean answer