The 5-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k 240 W/m K) or copper (k = 390 W/m K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C. If heat is transferred from the stove to the pan at a rate of 600 W, what is the temperature of the surface in contact with the stove for each of the two materials?

The 5-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k 240 W/m K) or copper (k = 390 W/m K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C. If heat is transferred from the stove to the pan at a rate of 600 W, what is the temperature of the surface in contact with the stove for each of the two materials?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam condenses at 100°C on the outer surface of a pipe with a thermal conductivity of 180 J/ms°C. The surface heat transfer coefficient of the water flowing in the pipe is 4000 J/m²s°C, and the heat transfer coefficient created by the steam condensing outside is 10000 J/m²s°C. The length of the pipe is 5 m and the thread diameter is 25 mm. Since the pipe thickness is 1 mm, calculate the total heat transfer coefficient and the rate of heat transfer from the condensed steam to the water at 15 °C
9.5 m 9.5 m The two configurations above both have a wall thickness of 550 mm, and a length of 20 m. Which of the two configurations above should a company use if it plans on using a fire clay brick refractory with k = 1.74 W/m. °C? Explain your choice. 9.5 m
A square 2014-T4 aluminum alloy plate 370 mm on a side has a 50-mm-diameter circular hole at its center. The plate is heated from 16°C to 56°C. Determine the final diameter of the hole. Answer: dfinal mm =
if you are unable to answer all parts, please do part 4 and 5. thanks
A long 3-mm diameter rod of steel (ρ = 7840 kg/m3, c = 460 J/kgK, k = 43 W/mK)has a uniform initial temperature of 650C. The rod is then suddenly immersed in alarge container of 25C water. The hot rod causes the water immediately surroundingthe rod to boil, giving rise to a heat transfer coefficient of 5600 W/m2K. The boilingstops when the rod reaches a temperature of 100C, at which time the heat transfercoefficient becomes 750 W/m2K. Find the time period during which boiling occursand the total time required for the rod to reach a temperature of 40C. Use acharacteristic length for this problem.
The 5-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k = 240 W/m.K) or copper (k = 390 W/m-K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C and heat is transferred from the stove to the pan at a rate of 1200 W. What is the temperature of the surface in contact with the stove for each of the two materials? Aluminum: T = i °℃ Copper: T = °℃ i
Consider a stainless steel spoon ( k = 8.7 Btu/hrft°F) partially immersed in boiling water at 200 deg * F in a kitchen at 75°F. The handle of the spoon has a cross section of 0.08in * 0.5in and extends 7 inches into the air from the free surface of the water. If the heat transfer coefficient at the exposed surfaces of the spoon handle is 3 Btu/hrft²°F, determine the temperature of the tip of the spoon handle. Assume that the heat loss from the tip of the spoon is negligible.
Good Day, Kindly help me with this problem, Thank you P.S. T= 30 degrees
Consider the base plate of a 750-W household iron with a thickness of L=0.6 cm, base area of A=170 cm2, and thermal conductivity of k=22 W/m.oC. The inner surface of the base plate is subjected to uniform heat flux generated by the resistance heaters inside. When steady operating conditions are reached, the outer surface temperature of the plate is measured to be 85 oC. Disregarding any heat loss through the upper part of the iron, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the plate, (b) obtain a relation for the variation of temperature in the base plate by solving the differential equation, and (c) evaluate the inner surface temperature.
40°C water with hwater = 800 W/m² K is flowing in a Pyrex tube. The inner and outer diameters of the tube are 25 mm and 35 mm. A thin metallic heater element bonded to the outer surface of the tube is being used to heat the water by transferring 600 W/m of thermal energy to the water flowing in the tube. The Pyrex tube and heater are covered with a 10-mm thick layer of foam insulation. The outer surface of the foam insulation is exposed to air at T = -5°C with hair = 12 W/m².K. The heater = air element must generate more than 600 W/m, because part of the heat being generated is lost to the air surrounding the foam insulation. Assume kp = 1.30 W/m K for Pyrex and k = 0.026 W/m K for the foam insulation. a) Find the temperature of the heater element needed to transfer 600 W/m of thermal energy to the water in the tube. b) Find the total rate at which the heater element must generate thermal energy. Water Pyrex tube, kp = 1.30 W/m.K = 40°C water hwater = 800 W/m².K Heater element Tair=…
kindly help me with this question. Thank you, I am having a hard time solving this
based on a large 4 cm thick plate that is initially at a uniform temperature of 20°C that is heated by passing it through a space maintained at 500°C. The plate remains in the space for a period of 7 min. Take the heat transfer coefficient to be 120-W/m2°C. Example 4-4 [k = 110-W/m°C, r = 8530-kg/m³, C, = 0.380-kJ/kg°C, a = 33.9 x 10-6 m²/s] The dimensionless distance from center to a point 0.4-cm below the outer surface is 0.5 0.8 none of the above 0.2