alfaO Hll 58%DI4:37 PM+1 (503) 782-794730 minutes agoThe 4-m diameter circular gate shown in the figure is located in the indined wall of a large reservoir containing water ty 9800 N/m3). Thegate is mounted on a shaft along its horizontal diameter. For a water depth of 10 m above the shaft determine the external mament thatwould have to be applied about the shaft to just open the gate. The weight of the gate can be neglected.ofSelect one:O a. 1.56*103 N.mO b. 1.07*10A5 N.mO C 1.86 10A5 N.mOn earh side leats in water. The specific eravity of the carton is 0.6.merged depth of the cube th)< o O

Diameter of circular gate d=4.0 mdepth of the C.G of the Gate from free surface h=10.0 munit wt…

The 4-m diameter circular gate shown in the figure is located in the indined wall of a large reservoir containing water ty 9800 N/m3) The Rate is mounted on a shaft along its horizontal diameter For a water depth of 10 m above the shaft determine the external moment that Would have to be applied about the shaft to just open the gate. The weight of the gate can be neglected, 60 10 m Stop Shaft /2

The 4-m diameter circular gate shown in the figure is located in the indined wall of a large reservoir containing water ty 9800 N/m3) The Rate is mounted on a shaft along its horizontal diameter For a water depth of 10 m above the shaft determine the external moment that Would have to be applied about the shaft to just open the gate. The weight of the gate can be neglected, 60 10 m Stop Shaft /2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION 8: A 180 kN force is supported by a vertical jet of water thru a nozzle. The velocity of the water is 15.4 m/s and the diameter of the jet is 2.2 cm. 36. Compute for the discharge of water from the jet. a. 0.04346 b. 0.00859 c. 0.00589 d. 0.00585 37. What is the velocity of the water before it reaches the maximum height? EVIE m a. 17.96т b. 30.77 m m c. 23.28- d. 3.436 38. What is the maximum height? a. 31.21 m c. 36.17 m b. 27.62 m d. 23.81 m
Q34. A 10 cm diameter jet of water éxerts a force of 2 kN in the direction of flow against a stationary flat plate which is inclined at an angle of 30° with the axis of the stream. Find, (i) Force normal to the plate (ii) Velocity of the jet (1) Mass flow rate of water kg/sec. Answer
Water flows through a venturi as shown in the figure at a flow rate of Q=1.3L/s. The inlet and throat diameters of the venturi meter are (D = 3.0 cm andd = 2.5 cm) respectively. The height of water column in the manometers L1 and L3 are 65 and 53 cm respectively. %3D What is the experimental dynamic head at the throat-{section2} (in m)? L3
. The head of water over an orifice of diameter 100 mm is 10 m. The water coming out from the orifice is collected in a circular tank of diameter 1,5 m. The rise of water level in this tank is 1.0m in 25 seconds. Also the coordinates of a point on the jet, measured from vena contracta are 4.30 m horizontal and 0.50 m vertical. Find the device coefficients.
Water flows through a new cast iron pipe at a velocity of 1.8 m/s. The pipe is 480 m long and has a diameter of150mm. Determine the head loss due to friction using Manning’s formula with n = 0.012.
z=174 m A B z=152 m z=91 m T = and Op ≈pg əx (Pump) C F A pump is used to deliver water from a reservoir to a large tank for a flowrate of 1310 L/s at 20 °C. The connecting pipe connects the reservoir at B with a square-edged entrance. From B to C, the pipe is 760 m long and has three gate valves, four 45⁰ elbows, and two 90° elbows. Gage pressure at C is 197 kPa. From F to G, the pipe is 760 m long and contains two gate valves (Kg.-0.136), four 90° elbows (K90-0.51) and connects the tank with an exit (Kext=1). All pipe is 508 mm in diameter (D) and made by cast iron ( = 0.26 mm). 1) Calculate the average velocity of water in the pipe. 2) Calculate the gage pressure at F. z=104 m 3) If the pump's efficiency is 80%, calculate the power input to the pump. 4) If the shear stress can be calculated using the equation D Op hL major 4 0x L Calculate the average wall shear stress in section F-G. G H
Water flows at 1.52 m/sec from a reservoir into a 900 mm diameter steel pipe that is 2286 m long and has a thickness of 25 mm. find the water hammer pressure developed by closure of a valve at the end of the line if the closure time is 8 sec. the velocity (celerity) of a pressure wave C=1440m/s, modulus of elasticity of water = 200 MPa and that of steel is 200,000 Mpa. Answer: 868.2 kPa
3 m water 8 m Pconerete= 2200kgm* wwww 6 m The dam shown in the figure is built of concrete having a density of 2200 kg/ m3 and rests on a solid foundation. Determine the minimum coefficient of friction between the dam and the foundation required to keep the dam from sliding at a water depth of 6.8 m. Assume that the dam is 100 m into the page. Your Answer:
An open tank filled with water and pulled at inclined surface as shown. Compute the acceleration which keeps the water surface at the position shown in fig. compute pressure at point(A) before and after acceleration. az ax 1.0m 1.40m A Static surface 3 Accelerated surface
Rainwater flows through the galvanized iron downspout shown in the figure below at a rate of 0.005 m³/s. Determine the size of the downspout cross section if it is a circular and it is completely filled with water. Neglect the velocity of the water in the gutter at the free surface and the head loss associated with the elbow. D= i 3 70 mm ↓ 4 m 3 m
Water flows into a conical vessel at a constant rate of Q cm³/s. The vessel has a height of 18 cm and a diameter of 10 cm at the top. When the water is 12 cm deep, the water level is rising at the rate of 0.115 cm/s. Find the value of Q.
The barge shown in the figure has the form of a parallelepiped having dimensions 10m by 26.7m by 3m. The barge weighs 4450KN when loaded and has a center of gravity 4m from the bottom. Find the metacentric height for the rotation about its long- est centerline, and determine whether or not the barge is stable. Use sp.wt. of water: 9.79KN/cu.m. 3m 4m W SCG 26.7 m