The 25-kg roll of paper has a radius of gyration kA - 90 mm about an axis passing through point A. It is pin supported at both ends by two brackets AB. The roll rests against a wall for which the coefficient of kinetic friction is - 0.3. Neglect the mass of paper that is removed. (Elguce 1) • Part A Determine the magnitude of the constant vertical force F that must be applied to the roll to pull off 1 m of paper in t = 3s starting from rest Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 Value Units Submit Previous Answers Resuest Answer 300 X Incorrect; Try Again; 5 attempts remaining 15 Provide Feedback Next >

The 25-kg roll of paper has a radius of gyration kA - 90 mm about an axis passing through point A. It is pin supported at both ends by two brackets AB. The roll rests against a wall for which the coefficient of kinetic friction is - 0.3. Neglect the mass of paper that is removed. (Elguce 1) • Part A Determine the magnitude of the constant vertical force F that must be applied to the roll to pull off 1 m of paper in t = 3s starting from rest Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 Value Units Submit Previous Answers Resuest Answer 300 X Incorrect; Try Again; 5 attempts remaining 15 Provide Feedback Next >

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.80P

See similar textbooks

Related questions

Q: The square steel plate has a mass of 1990 kg with mass center at its center G. Calculate the tension…

Q: The 17-kg wheel is rolling under the constant moment of M = 85 N-m. The wheel has radius r= 0.50 m,…

Q: The 136-kg spool has a radius of gyration about its mass center of ke = 300 mm If the couple moment…

Q: The 16-kg wheel is rolling under the constant moment of M = 60 N-m. The wheel has radius r= 0.50 m,…

Q: A device consists of eight balls each of mass 0.7 kg attached to the ends of low-mass spokes of…

A: Given Data Mass of ball is : mb=0.7 kg Length of spokes is : Ls=1.4 m Radius of ball is : rb=0.7 m…

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.

Question

100%

Review
The 25-kg roll of paper has a radius of gyration
kA = 90 mm about an axis passing through point A. It is
pin supported at both ends by two brackets AB. The roll
rests against a wall for which the coefficient of kinetic
friction is pe = 0.3. Neglect the mass of paper that is
removed. (Eigure 1)
Part A
Determine the magnitude of the constant vertical force F that must be applied to the roll to pull off 1 m
of paper in t = 3 s starting from rest
Express your answer to three significant figures and include the appropriate units.
Figure
< 1 of 1
Value
Units
Submit
Previous Answers Resuest Answer
300
x Incorrect, Try Again; 5 attempts remaining
125
Provide Feedback
Next >

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
Can the uniform bar of weight W remain at rest in the position shown?
Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
The 320-lb homogeneous spool is placed on the inclined surface. Determine the vertical force P that is required to keep the spool in the position shown. Assume that there is enough friction to prevent slipping at A.
End B of the uniform 2.7-kg bar AB is connected to a small roller that moves in a horizontal slot. The other end of the bar is pinned to the homogeneous 1.8-kg disk that rolls without slipping on the vertical surface. The spring attached to A has a free length of 0.3 m and a stiffness of 58 N/m. After the system is becomes horizontal. Determine the magnitude of the force P that acts on the bar at B. 2.1 m 0.24 m 0.9 m www 1.8 kg 1.5 m 2.7 kg P
The solid homogeneous cylinder shown has a mass of 30 kg and is rotating at 1200 rpm clockwise about a fixed horizontal axis through O. The coefficient of kinetic friction between the brake and the cylinder is 0.20. If the tension in the spring when the brake is applied is 100 N, determine the time required for the cylinder to stop rotating. Neglect the thickness of the vertical members. (Draw FBD)
Correct and complete solution
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
Determine the smallest horizontal force P that would push the homogeneous cylinder of weight W over the curb. Neglect friction.
The figure is a model for member CDE of the frame described in Prob. 4.10. Draw the FBD of the member, neglecting its weight. Count the unknowns.
Problem (3): theangle e in the figuce is geadualy increased fram Zcro. a Tepart a EBD of Th cylin dar. b. Find thevalue of o at which the Slithd cylinder of mass m will begin to slip.