The square steel plate has a mass of 1990 kg with mass center at its center G. Calculate the tension in each of the three cables with which the plate is lifted while remaining horizontal.

Q: The 2 m long bar BC weighing L touches the polished surface at a point 1 m away from point A. The…

A: A smooth surface will not exert any friction force on object except the normal reaction. The normal…

Q: 3. Determine the smallest horizontal force P that would push the homogenous cylinder of weight W…

A: As per given question  We have to find force required to puah the cylinder

Q: The 42-kg homogeneous smooth sphere rests on the 26° incline A and bears against the smooth vertical…

A:

Q: The jib crane is designed for a maximum capacity of 5 kN, and its uniform I-beam has a mass of 200…

A: To Find : The resultant force at x=0.8m. Given :  The maximum capacity is 5kN The mass of beam is…

Q: (3) Draw and show the projected component of the 400-lb force along member AC. 400 lb B

A: Given:Magnitude of force at A = 400 lbAngle between the member AC and AB is To find:The projected…

Q: Because of long-term loading from the 900-N tension in the power line, the uniform utility pole has…

A:

Q: The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is…

A:

Q: The top of the folding workbench has a mass of 54 kg with mass center at G. Calculate the magnitude…

A:

Q: The 43-kg homogenecus smooth sphere rests on the 36° incline A and bears against the smooth vertical…

A:

Q: 1. In the figure shown, compute the resultant of the three forces and locate its intersection with…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: The 46-kg homogeneous smooth sphere rests on the 32° incline A and bears against the smooth vertical…

A: When an amount of push or the pull applied on the object, it has the ability to change its state…

Q: G, and G2 respectively, determine the tension force in cable AB and the reaction forces at point 0.

A:

Q: homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs. Motion…

A:

Q: The bobcat loader (Figure Q3) has a mass of 1200-kg, shows the center of mass is at G1. If there is…

A:

Q: The 87-kg homogeneous smooth sphere rests on the ( 2.4/4) incline A and bears against the smooth…

A:

Q: The compound bar is supported by a thrust bearing at A, a slider bearing at B, and the cable CD.…

A: Given Compound bar To find Tension in cable Bearing A reaction

Q: Question 2: Calculate the tension force that is being exerted on the box of mass 50kg. Refer the…

A:

Q: The 45-kg homogeneous smooth sphere rests on the 42° incline A and bears against the smooth vertical…

A: Mass of sphere, m=45 kgInclination angle of A, θ=42o

Q: . each cable has vector, as seen in fig. Calculate the maximum mass of the sphere so that the…

A:

Q: One of the smooth verticai walls supporting end B of the 235-kg uniform shaft is turned through a…

A:

Q: Masses M1 and M2 are held on the frictionless inclined plane by a rigid inextensible bar of length l…

A: The free-diagram is shown in the figure below.

Q: A uniform sphere of weight W rests between a smooth vertical plane and a smooth plane inclined at…

A: Weight of an object is defined as mass times the acceleration due to gravity. The weight of the…

Q: m The hoist supports an engine Determine magnitude of the force created by the engine mass

A: tanθ1=a+ba-btanθ1=2.2+1.12.2-1.1θ1=71.56o∑Fv=0RA+RB-mg=0RA+RB=mgRA+RB=175×9.81RA+RB=1716.75 N ,…

Q: The boom shown inFig. weighs 2600 N and isattached to a frictionless pivot at itslower end. It is…

A: Given Data: The weight of the bloom is W1= 2600 N. The weight of the block is W2 = 5000 N. The…

Q: The top of the folding workbench has a mass of 46 kg with mass center at G. Calculate the magnitude…

A:

Q: The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 230…

A:

Q: A 42-kg homogenous smooth sphere rests on the 26° incline A and bears against the smooth vertical B.…

A:

Q: 1.45 r 2.05 r

A: Given,  Applying the Cosine and sine rule to get the required angles

Q: Find the tensile force T1 in cable 1. (Write your result in N) Answer b) Find the tensile force T2…

A:

Q: 7.5' |A 6.8' 0.6' B 2.4' 3.6' OFF HIO

A:

Q: The ramp of a ship has a weight of F Ib acts in the center of gravity at G. The ramp is supported by…

A:

Q: The square steel plate has a mass of 1690 kg with mass center at its center G. Calculate the tension…

A:

Q: The homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs.…

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.