The 200-mm-diameter aluminum cylinder supports a compressive load of 300 kN. Determine the average normal and shear stress acting on section a-a. Show the results on a differential element located on the section.

The 200-mm-diameter aluminum cylinder supports a compressive load of 300 kN. Determine the average normal and shear stress acting on section a-a. Show the results on a differential element located on the section.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Horizontal plates are connected to the bar AB whose length varies linearly from zero to HA, as…

Q: 6kN and 1.0kNm loads are applied to the top of the 62-mm-diameter cast-iron as shown. Determine the…

Q: Take the section AB, construct the FBD and label the internal loadings, determine the normal stress…

Q: The rectangular bar is connected to the support bracket with a 12-mm-diameter pin. The bar width is…

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: ) If the load has a weight of 600 lb, determine the maximum normal stress developed on the cross…

A: An internal resisting force which is applied by the molecules of the object so that the shape of the…

Q: The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is…

A: Diameter of pin, d=11 mm=0.011 mBar width, w=60 mm =0.060 mBar thickness, t=10 mm=0.010 mThe average…

Q: The solid circular rod has a cross-sectional area of 450 mm². It is subjected to a uniform axial…

Q: The bar has a 100 mm by 15 mm rectangular cross section. The allowable normal and shear stresses on…

Q: The beam is subjected to the load at its end. Determine the maximum principal stress at point B.

A: Determine normal stress due to axial load Due to shear load there will be bending moment at B…

Q: The rectangular bar is connected to the support bracket with a 26-mm-diameter pin. The bar width is…

A: Given data:- Diameter of pin =26mm. The bar width (w)= 60 mm the bar thickness (t) = 15 mm. Each…

Q: 25 kN 20 kN 30 kN 14 -1.5 m- 3 m 3 m

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: The rectangular bar is connected to the support bracket with a 27-mm-diameter pin. The bar width is…

Q: re, determine the state A and at point B. Dra plume elements at A am results.

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

Q: Problem 4: Determine the resultant intermal loadings acting on the cross section through point B of…

A: To determine the internal reactions at point B.

Q: The solid circular rod has a cross-sectional area of 440 mm². It is subjected to a uniform axial…

Q: The hook is subjected to the force of 60 lb Determine the state of stress at point A at section a-a.…

A: Part A: Write the given data. F=60 lbd=0.5 in

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

Q: A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section…

A: Calculated normal stress at A, B and C and y position where normal stress equals zero

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

Q: The rectangular bar carries a load of P = 102 KN and is connected to the support bracket with a…

Q: Determine the cross-sectional area of the shaft. Answer: A = 1 mm²

A: Given that :Vertical shaft diameter, d=20 mmthickness of plate, t=21 mmCollar thicknesses,…

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

Q: is it okay to solve this even if it is not in equilibrium? Why?

A: Solution:

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: Given:- P=2kip,Width of section of bar with hole,w1=1.875 inch,Width of section of bar without…

Q: The joint fastend togather using two bolts with the plate thickness of 5mm. Determine the required…

A: given; shear stress of bolt(τ)=350MPalets take diameter of bolt=dacting load on plate(P)=40KN

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: The solid circular rod has a cross-sectional area of 360 mm². It is subjected to a uniform axial…

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

Q: If the allowable tensile stress for wires AB and AC is sallow = 200 MPa, determine the required…

Q: The solid circular rod has a cross-sectional area of 350 mm². It is subjected to a uniform axial…

Q: The solid bar has a diameter of 50 mm. The two forces and the x-y-z coordinate system which is…

Q: The joint is subjected to the axial member force of 6 kips. Determine the average normal stress…

Q: The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is…

A: The diameter of pin, d = 19 mmThe bar width, b = 70 mmThe thickness, t = 15 mmThe average shear…

Q: The horizontal shaft with a diameter of d-41 mm is supported by a thrust collar that rests on a…

A: diameter of the shaft d=41 mmthickness of the collar= 24 mmthickness of the plate =31 mmouter…

Q: The solid bar has a diameter of 50 mm. The two forces and the torque Tx are acting at the origin of…

Q: The rectangular bar is connected to the support bracket with a 14-mm-diameter pin. The bar width is…

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a…

A: F1= 11 kN= 11000 N a= 250 mm b= 100 mm c= 90 mm θ= 40∘ Diameter, d= 29 mm Thickness, t= 31 mm To…

Q: The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial…

Q: The 3/4-in.-diameter shaft is subjected to the loading shown. Determine the stress components at…

A: Given data as per the question The diameter of shaft =3/4 in considering the structure and forces…

Q: The sign is supported by a hollow structural tube of 15 in. outer diameter and 0.5 in. wall…

Q: The bar has a cross-sectional areao of 490(10-6)m2. It is subjected to triangular axial distributed…

A: Area of the cross section To determine:The average normal stress in the bar

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The 200-mm-diameter aluminum cylinder supports
a compressive load of 300 kN. Determine the average normal
and shear stress acting on section a-a. Show the results on a
300 kN
differential element located on the section.
30°
a

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Final solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bar has a 80 mm by 20 mm rectangular cross section. If P = 90 kN, determine the normal stress magnitude acting on surface a-a. 80 mm 62° a P = 90 kN
The 0.97 in diameter rod is subjected to the loads shown. Determine the normal and shear stress at point B.
The solid 0.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 500 lb/ft. Two concentrated loads also act on the rod: P = 1900 lb and Q = 900 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x = 8 in. (b) x = 24 in.
The joint is subjected to the axial member force of 6 kips. Determine the average normal stress acting on sections AB and BC. Assume the member is smooth and is 1.5 in thick. . Tip: You can determine the forces by making a FBD in a concurrent point. 1.5 in B 20⁰ 4.5 in. 6 kip 50⁰
The bars of the truss each have a cross-sectional area of 1.25 in2. Determine the average normal stress in members AB, BD, and CE due to the loading P = 6 kip. State whether the stress is tensile or compressive.
The screw of the clamp exerts a compressive force of 500 lb on the woodblocks. Sketch the stress distribution along section a–a of the clamp. The cross section is rectangular, 0.75 in. by 0.50 in.
The 20 mm diameter rod is subjected to the loads shown.(a) Determine the state of stress at point and show the results on a differential element located at this point.(b) Using Mohr's circle, determine the maximum normal stress and the maximum in-plane shearing stress at point A and show the associated stress states on appropriately oriented elements, for cach case.
1. The pictured link acts as a part of the elevator control for a small airplane. If the attached aluminum tube has an inner diameter of 25 mm and a wall thickness of 5 mm, determine the shear stress in the outer and inner surfaces of the tube when a cable force of 600 N is applied to the cables. Also, sketch the shear-stress distribution over the cross-section.
The elbow of the pipe has an outer radius of 0.75 in. and an inner radius of 0.63 in. If the assembly is subjected to the moments of M = 25 lb # in., determine the maximum stress at section a–a.
The man has a mass of 100 kg and center of mass at G. If he holds himself in the position shown, determine the maximum tensile and compressive stress developed in the curved bar at section a–a. He is supported uniformly by twobars, each having a diameter of 25 mm. Assume the floor is smooth. Use the curved-beam formula to calculate the bending stress.
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb/ft2, determine the state of stress at points Cand D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe. 6 ft 3 ft 上 A B x 12 ft 150 lb/ft²
9 mm A .9 mm 96 mm 60 mm P 9 mm If the 9 mm hole is drilled through the plate determine the radius of the fillets such that the maximum stress value is the same for the hole %3D and the fillets for a applied force of P = 10 kN.