The 12 kN.m torque is applied to the free end of the 5-m steel shaft. The angle of rotation of the shaft is to be limited to 3o. (a)Find the diameter d of the smallest shaft that can be used. (b) What will be the maximum shear stress in the shaft? Use

The 12 kN.m torque is applied to the free end of the 5-m steel shaft. The angle of rotation of the shaft is to be limited to 3o. (a)Find the diameter d of the smallest shaft that can be used. (b) What will be the maximum shear stress in the shaft? Use

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the maximum allowable shear stress in the shaft. Calculate the minimum diameter required for the shaft. Answer: d = i in.
A shaft composed of three segments and fastened to rigid supports. Determine the maximum shear stress developed in each segment. (Please don't skip any mathematical step and please show all the working)
he compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel.
A steel shaft with a length of 3.00 m. One meter of the steel is contained in a brass tube and firmly attached. The diameter d1 = 70 mm and the diameter d2 = 90 mm. Brass G = 39GPa and steel G = 77.20 GPa. Determine: The torque that can be applied if the deformation at one end is 10 degrees. Answer: T = 8.64 kN – m The torque that can be applied if the maximum shear stress in brass is 70MPa and in steel is 110MPa. Answer: T = 6.352 kN – m Recommendation: analyze by segments. The first segment is only brass, then the composite part between brass and steel, and the last part only steel. In the composite segment, use only one material. In this same segment, equalize the deformations.
A hollow shaft with an outside diameter of 113 mm and an inside diameter of 103 mm is subjected to both a torque of T= 6.2 kN-m and an axial tension load of P = 106 kN, as shown. Determine the normal and shear stresses at point H and show them on a stress element. y (1) Answers: Ox = i MPa, oy = i MPa, Txy = i MPa.
If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d = 100 mm with 3 mm thick walls is T = 12 kNm, which of the following is closest to %3D the magnitude of the minimum shear stress developed on that section? Select one: O A. 262 MPa O B. 501 MPa O C. 279 MPa O D. 533 MPa
I need answer within 5 minutes please please with my best wishes
The steel shaft is made from two segments: AC has a diameter of 0.5 in, and CB has a diameter of 1 in The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft G₁ = 10.8 (10¹) ksi (Figure 1) Figure 0.5 in. 8 in. D 500 lb-ft 12 in. 1 of 1 1 in. B Determine the maximum shear stress in the shaft. Express your answer in kilopounds per square inch to three significant figures. Tmax Submit Provide Feedback IVE ΑΣΦ. 11 | vec Request Answer ? ksi
Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear strain is γmax = 640 × 10-6rad Igo, inside andThe outside diameters are 120mm and 150mm, respectively.a. What is the maximum axial strain?b. Maximum axial stress?c. What is the maximum torque (T) meeting the above conditions?
2. The maximum torsional moment a solid shaft can bear is T = 0.2r kN . m. If the allowable shear stress of the material is [t] = 50 MPa, design the diameter of the shaft based on the strength condition
a. A solid cireular shaft of length of 3 m and diameter of 50 mm rotates at 1200 rpm by a 400 HP electric motor at its middle. It derives two machines of 150 HP and 250 HP at left and right ends of the shaft, respectively. Determine the maximum shear stress and relative displacement of the two ends of the shaft. Take G = 85 GPa.
3. Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the pulleys as shown in the figure, determine the maximum shear stress in each segment and the angle of rotation of pulley D relative to pulley A. Use G = 28 GPa for aluminum. a. Tab= b. Tbc= C. Tbc= ad= 1100 N·m 800 N·m D C 900 N·m 600 N m B A 2 m3 m2 m