The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680 MPa, and for the bronze (σY)br=490 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.

The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680 MPa, and for the bronze (σY)br=490 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the final measurements of the length and diameter of the following bar that is subjected to a force of 50kN. Assume that the material behaves elastically with a modulus of elasticity of 200GPa and a Poisson's modulus of 0.32. P = 50 kN 600 mm 20 mm E=200 GPa V=0.32 P = 50 kN
A suspension system of a mountain bike is held by a pin at point C and supported by a shock absorber BD. If the bike is designed to withstand a load P = 1500N with safety factor F₁ = 2, ultimate shear stress t = 150 MPa and ultimate tensile stress Ou = 360 Mpa, determine pin B and pin C diameters.
The cross-sectional area of the bar is 5 cm². Use E = 70 GPa for aluminum, and E = 200 GPa for steel. L. Aluminum Steel Aluminum 80 kN 20 kN - 30 kN + 70 kN A D B - 3 m - - 4 m · 5 m
The pin is used to connect the three links together. Due to wear, the load is distributed over the top and bottom of the pin as shown on the free-body diagram. The diameter of the pin is d = 0.39 in. (Figure 1) Figure 1 in.- 400 lb 800 lb -1.5 in. 1 in. 400 lb Id W₂ a Part A Determine the maximum bending stress on the cross section at the center section a-a. Hint: For the solution it is first necessary to determine the load intensities w₁ and 2. Express your answer in kilopounds per square inch to three significant figures. max = Submit Provide Feedback -- ΑΣΦΑΤΗ1 VO Request Answer vec H ? ksi Next >
A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2 is of 15 mm diameter and 50 mm long and section 3 is 20 mm square and 40 mm long. The bar is subjected to an axial tensile load which induces a stress of 20 MN/m2 on the smallest cross section. Determine the total Increase in the length of the bar when the load is applied. For copper E=100 GN/m2.
The five-bolt connection must support an applied load of P = 4600 lb. If the average shear stress in the bolts must be limited to 32 ksi, determine the minimum bolt diameter that may be used for this connection. 00000 Answer: dmin = i ! in.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 14 mm and an elastic modulus of E= 65 GPa. The steel rod has a diameter of 18 mm and an elastic modulus of E= 215 GPa. Assume a = 3.2 m, b = 1.3 m, and c = 1.4 m. What is the magnitude of load P that is necessary to displace point A 10 mm to the left? (1) (3) A 4 Answer: P = i B (2) D KN
The stepped rod is made up of two different materials A and B of lengths 80 cm and 1.2 m respectively. The diameters of materials B and A are 2.5 and 3.5 cm respectively. The modulus of elasticity of materials A and B are 250 and 150 GPa respectively. The elongation of the rod is the same for both the materials. A total tensile load of 40 kN is applied to both the materials A and B together. Calculate the load in each material.
just final answer A rigid component ABC is supported by a pin-connected member (1). The member has a rectangular cross-section with dimensions of 54 mm and 48 mm. The elasticity modulus of the material is 169 GPa. If L1=2421 mm, L2=1226 mm, L3=2272 mm, and L4=2072 mm; Determine the maximum normal stress (MPa) in member (1) without buckling.
The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A and C are stress-free. The load P is then applied and there is a temperature change in the steel rods. P = 38 kips with the stresses in the two steel rods equal. Assume that there is no buckling in the rods. The coefficient of linear expansion is 6.5 x 10^–6 per degree F and E = 29 x 10^6 psi for steel. a. Determine the change in temperature. Indicate increase or decrease in temperature. b. Determine the axial deformation of the steel rod at A (in inches). c. Determine the axial deformation of the steel rod at C (in inches).
Determine of the internal resistance force of each segment of the bar shown below, and the total elongation of the bar. Let: The forces acting P₁=150kN, P₂=250kN, P3=200kN, P4=50KN. Areas of the bar segments A1=1000mm, A2=2000mm, A3=1000mm. E=200Gpa -2000 mm -1000- ** -1500 P₂ 1b P3 P4 P₁ A₁ la a B A₂ b C A3 C C D
pts) The rigid L-shaped bar show below is supported by pin at A, steel rod at L, and titanium rod at C. Determine the force in the rods when the 2 k/ft distributed load is applied on arm CA. Determine the reaction at support A. Also, determine the strains in the steel and titanium rods. Show the free body diagrams. Show all calculations. See attached Material Properties Table for required parameters in your calculation. Rod: Steel A-36 Diameter = 3/4" L = 5 ft Rigid 2 kip/ft C 8 ft Rigid Rod: Titanium Alloy Diameter = 3/4" L = 4 ft L 5 ft A