2-A-The bar is pinned at A and supported by two aluminum rods, each having a diameter of 25 mm and a modulus of elasticity Ea70 GPa. If the bar is 03m 03m assumed to be rigid and initially vertical, determine the displacement of the end B when the force of 10 kN is applied. 10 AN 0.6 m 03m

Q: Learning Goal: To determine the in-plane principal stresses and maximum shear stress along with…

A: Step 1: Step 2: Step 3: Step 4:

Q: The results of a tensile test are: Diameter of the specimen Gauge length Load at limit of…

A: Given: The diameter of the specimen is, d=10 mm. The value of gauge length is, l=40 mm. The load at…

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: A gauge # 10 HSLA steel for an automotive application has a Young’s modulus of 200 GPa, a yield…

A: Find the punch force required

Q: Which material has the greatest UTS?

A: The ultimate tensile stress is the maximum stress in the material corresponding to the strain.

Q: Comparison of compressive strength compared to standard compressive strength comparison

A: Compressive strength test, mechanical test measuring the maximum amount of compressive load a…

Q: A) An engineer works for a company that has many gray cast iron rods of different diameters and…

A: Given :Load P = 10 kip Material : grey cast iron

Q: Q1: Find a relation between true strain () and reduction in area (r)?

A:

Q: -Answer the following questions by referring the given figure: (0.5 material specification + 0.5…

A: Dear student,                    As you have already have answer of first three subparts so I am…

Q: Which material should be chosen when high strength is required

A: Given: To define: Which material should be chosen when high strength is required

Q: 4. A 25 mm diameter steel rotating shaft in a machine is loaded as follows: $ = 25mm Rotating M T…

A:

Q: If 80% of samples has a compressive strength greate than x, calculate the value of x (to 1 decimal…

A:

Q: Choose the LETTER from the stress strain graph that matches the stress strain graph attributes…

A: Stress-strain curve of material provides us the information about the stress and strain in material…

Q: Given data : Work done=3600 J Displacement=2.1 m Determine Force applied

A: Work done = Applied Force X Displacement

Q: The state of stress at a point in a structure is depicted in Fig. 1. Calculate the normal stress and…

A: Given Data:   To Find: (a) The normal stress σ. (b) The angle θ.

Q: Question 5 Answer the following questions concisely (no more than half a page per question): a What…

A: Since you have posted a question with multiple subparts, we will solve first three sub parts for…

Q: 2. A rectangular steel bar 0.5 inch thickness by 1.5 inches width and 220 ft long is subjected to a…

A: Given: Thickness of the steel bar is 0.5 in. Width of the steel bar is 1.5 in. Length of the steel…

Q: Pls answer thank you! A circular rod is 128 mm in diameter and carries gauge marks placed 50.8 mm…

A:

Q: In the First project: you have been asked to perform tensile testing for four different materials…

A:

Q: In the graph, the module of toughness can be shown to be represented by: A) The area associated…

A:

Q: The following data are obtained from a tensile test of a copper specimen. - The load at the yield…

A: Stress: When a component or a part is subjected to any external force, the resisting force will be…

Q: This subject is strength of materials show complete and clear solution with free body diagram and…

A:

Q: .. An machine part is being tested with a load of 63,000 lb. The allowable tensile stress is 10,000…

A: Given:Allowable Tensile Stress on machine=σmaximum=10000 psi(pound per square…

Q: Problem 1: Which metal and or metal alloy material will not experience either plastic deformation or…

A: Given: L= 380 mm load P= 24500 N

Q: PLS MADE A FBD DIAGRAM !!!!! easy!!!!!! there is a rubber mat circled in yellow that is non slip and…

A: It is asked to calculate the reactions in the rubber mat.

Q: Tensile test had made to cylinder shape with diameter 3.0 In and length 5.7 In. It had maximum…

A:

Q: Please answer these three questions. Thank you!   A material has a Poisson’s ratio of -0.2 . Which…

A: Givenpart 1A material has a Poisson’s ratio of -0.2 . Which of the following is true?a. Strain is…

Q: 3. What do zeros in the stiffness matrix indicate?

A: We have to note about What do zeros in the stiffness matrix indicate?

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in ension. An axial load…

A:

Q: 2. A wire is stretched between 2 rigid posts separated by a distance L. If the surrounding…

A:

Q: You have built the majority of the tension testing machine, but much of the instrumentation is still…

A: The diameter is

Q: An alloy steel having a diameter of 0.45 in. extends 0.002 in. over a gage length of 2.2 in. due to…

A:

Q: Given the following stress-strain graph: a. is the modulus of elasticity of "A-514" greater, less or…

A: (a): the modulus of elasticity of A-514 is same asA-572 because the slope of initial stress strain…

Q: P= The magnitude of the applied force (N). AL = amount of shrinkage of the sample (mm). -…

A: In this problem, we will complete the table for four forces. Calculate the parameters for force…

Q: What is the maximum load that can be applied in our Universal Testing Machine located in Engineering…

A: A machine used to examine the elongation or contraction of the material under pulling and pushing…

Q: A rectangular rosette is placed on a steel plate and indicates the following strains: Ej = 563 µm/m…

A:

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.