The 0.67-lb slider moves freely along the fixed curved rod from A to B in the vertical plane under the action of the constant 1.1-lb tension in the cord. If the slider is released from rest at A, calculate its speed v as it reaches B.

The 0.67-lb slider moves freely along the fixed curved rod from A to B in the vertical plane under the action of the constant 1.1-lb tension in the cord. If the slider is released from rest at A, calculate its speed v as it reaches B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q-2: Through a very narrow gap of height 'h', a thin plate of large extent is pulled at a velocity V. On one side of the plate oil of viscosity m,and on other side oil of viscosity m². Calculate the position of plate so that : (i) The shear force on two sides of plate is equal.
The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of 0.753 in. If a force of 15 kip is applied to the bar, determine the angle of tilt of the bar in degrees. 3.5 ft 2.5 ft E D -1.25 ft- 0.75 ft' 1 ft 15 kips
The device shown is a part of an automobile seat- back-release mechanism. The part is subjected to the 4-N force exerted at A and a 300-N•mm restor- ing moment exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force. y F =4 N 10 mm 15° 40 mm 300 N-mm
Q2. Member ABC is supported by two fixed supports at points A and C. The member has heights of 100mm at points A and C whereas the height is 600mm at point B. A point torque of 10KN.m is applied Im away from the point A. Determine the reactions at supports A and C. Write vour results in the box below. Use G-100GPA. B A T= 10 kN.m 100 mm 600 mm 1 m 1 m 2 m
200-Ib block is suspended from an inextensible cable which is wrapped around a drum of 1.3-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of Inertia lG = 10 Ib-ft-s^2 At the instant shown, the velocity of the block is 5 ft/s directed downward. Knowing that the bearing at A is poorly lubricated and that the bearing friction is equivalent to a couple M of magnitude 60 Ib-ft, determine the velocity of the block after it has moved 4.2 ft downward (in ft/s).
For a helical spring the slope of helix may be assumed small, is required to transmit a maximum pull of 1 kN and to extend 10 mm for 100 N load. The mean diameter of the coil is to be 100 mm. The diameter of wire is 100 mm. Calculate the no. of coils required? (G = 100 GPa and fs = 100 MPa)
Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the answer is negative.) A prybar is used to remove a nail as shown. Determine the moment of the 240 N force about the point O of the contact between the prybar and the small support block. (in N-m)
Consider the frame as shown in the figure. A moment of 80 kN-m acts at the joint O, given that the support at B fails at any moment greater than 18 kN-m. Then support B is (a) Unsafe (c) Just Safe A L, EI D L, EI D 80 kNm B L, EI L, EI C (b) Safe (d) Cannot be determined
5.
If the clamping force at G is 900 N, determine the horizontal force F that must be applied perpendicular to the handle of the lever at E. The mean diameter and lead of both single square-threaded screws at C and D are 25 mm and5 mm, respectively. The coefficient of static friction is μs = 0.3.
Strength of materials A cast-iron crank has a section on the line AB of the form shown. Show how to determine the greatest compressive and tensile stresses at AB, normal to the section, due to the thrust P of the connecting rod at the angle shown. If the stresses at the section must not exceed 75 MN/m2, either in tension or compression, find the maximum value of the thrust P.