þ in. 2 in. 30 kips B 30 kips 30 in. 40 in.

Q: 2.5m 3.5m 4.0m- The 4-mm diameter cable BC is made of steel with E = 200 GPa. Knowing that the…

A:

Q: A metal bar AB of a weight W is suspendedby a system of steel wires arranged as shown in thefigure.…

A: Given:   Let,L=Length of side perpendicular to bar=5ina=Length of side parallel to bar=2inHypotnuse…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown below. Knowing…

A: According to the question DAB=1.25 in DBC=0.75 in we need to find  (a) Normal stress in the AB  (b)…

Q: A short wooden post supports a 6-kip axial load as shown. Determine the stress at point A when (a)…

A: Determine the area and moment of inertia of the cylindrical body,

Q: A steel load binder is loaded as shown. Determine the required solid diameter needed for section AB…

A:

Q: For the clevis connection shown, the shear stress in the 0.21-in.-diameter bolt must be limited to…

A: Given: Let us consider the given data, Shear stress,  τ=39 ksi=39×103 Psi Bolt's diameter, d=0.21 in…

Q: Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing…

A:

Q: For the truss and loading shown, determine the magnitude of the normal stress(in psi) in member CE,…

A:

Q: 28. Determine the stress, in MPa, in member DF if its cross sectional area is 900 mm². B

A: Given data

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the largest load…

A:

Q: From the following system, determine the moment about point O generated by the force F1.  and the…

A: Given data, The applied force, F1  = 50 N Coordinates of point C = (631, 576, -330) Coordinates of…

Q: f P= 8.571 kN, Determine the stress in member CE assuming that the area in steel is 24 mm?. A 1.4 m…

A:

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown Knowing that the…

A: Solution:

Q: Two cylindrical cross-section rods AB and BC, which are fixed to the wall and welded together at…

A:

Q: Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing…

A:

Q: Determine the diameter (in mm) of the largest circular hole that can be punched into a sheet of…

A:

Q: For the steel truss and loading shown, determine the deformation (in inches) of  member BD, knowing…

A: Using method of sections to calculate force in member BD

Q: The truss shown consists of wooden members. Knowing that each member has a 100 x 100 mm. square…

A:

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the largest load…

A:

Q: determine the largest load P t

A:

Q: Knowing that for the beam shown the allowable stress is 80 MPa in tension and 100 MPa in…

A:

Q: P A y P B P D E y F

A: find the deformation in the member BD.

Q: An offset h must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall…

A:

Q: 1.3 Two solid cylindrical rods AB and BC are welded together at B and = loaded as shown. Knowing…

A: Given P = 10 kips To find Average normal stress

Q: Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: The bearing stress at A in member AB is 67488 psi.

Q: The truss shown consists of wooden members. Knowing that each member has a 100 x 100 mm. square…

A:

Q: A 6.87-m-long steel rod must not stretch more than 2.5 mm and the normal stress must not exceed 181…

A:

Q: 1. The reactions at A and C. 2. The maximum shear in the shaft. 3. The angle of twist in the shaft.

A:

Q: In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each…

A:

Q: Two horizontal 5.92-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: P = 5.92 kip d = 0.82 inch t = 0.5 inch

Q: 3 in. 2 in. В C P Q 30 in. 40 in.

A:

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 =…

A: Write the expression for stress developed in the cylindrical rod.

Q: Determine the uniform cross-section of the truss members BC, BE and AE, if the allowable stresses…

A: Given:The allowable stresses in tension, σT=150 psiThe allowable stresses in compression, σC=125…

Q: Two wooden members of uniform rectangular 150 mm cross-section are joined by a simple glued scarf…

A: Given: Maximum permissible shear stress τmax=620kPa

Q: wo wooden boards, measuring 15 mm thick and 225 mm wide, are joined by the socket joint shown.…

A:

Q: A rod must not stretch more than 6  mm when the tension in the wire is 8 kN. Knowing that E = 105…

A:

Q: A block of 10-in. length and 1.8 3 1.6-in. cross section is to sup-port a centric compressive load…

A: length, L=10-in Sides of the block a=1.8 in,   b=1.6 in normal stress = 18 ksi…

Q: Two solid cylindrical rods AB and BC are welded together at Band loaded as shown. Determine the…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A:

Q: a steel rod AB with the diameter of 5.8in is inserted into a circular hole at the end C of th wooden…

A:

Q: Determine the stress acting in members AB, BD and BE of th members is 15 in2

A: Need to determine Stress.

Q: The rigid bar EFG is supported by the truss system shown. Knowing that the member CG is a solid…

A: force p=5000 lbdiameter of Cg section D=0.75 inchto findnormal stress in CG

Q: Link BD consists of a single bar 1 in. wide and 12 in. thick. Knowing that each pin has a 38-in.…

A: The provided system is shown below.To determine:

Q: 4. The bars of the truss below each are made of 2 in. diameter rods. If the maximum average normal…

A: Diameter of rod, d = 2 inmaximum average normal stress = 30 ksi