Tensile StrengthA PL 3/8 x 7 tension member is connected with three 1-inch-diameterbolts, as shown in Figure P3.2-1. The steel is A36. Assume that Ae = An%3Dand compute the following.a. The design strength for LRFD.b. The allowable strength for ASD.PL %x7O o o

Tensile Strength A PL 3/8 x 7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3.2-1. The steel is A36. Assume that Ae = An and compute the following. a. The design strength for LRFD. b. The allowable strength for ASD. PL %x7

Tensile Strength A PL 3/8 x 7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3.2-1. The steel is A36. Assume that Ae = An and compute the following. a. The design strength for LRFD. b. The allowable strength for ASD. PL %x7

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A double-angle shape, 2L7×4×3/s , is used as a tension member. The two angles are connected to a gusset plate with 7/8-inch- diameter bolts through the 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used. a. Compute the design strength. b. Compute the allowable strength. 2/2" 7" 3" 1/2" 2L7 × 4 × 3/s FIGURE P3.4-5
A double-angle shape, 2L7 3 4 3 3⁄8, is used as a tension member. The twoangles are connected to a gusset plate with 7⁄8-inch-diameter bolts throughthe 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used.a. Compute the design strength.b. Compute the allowable strength.
A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area. Answer: о о lo O o
An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
Problem (4): A36 steel is used for the tension member shown in Figure below. a. Determine the nominal strength based on the gross area. b. Determine the nominal strength based on the net area. PL 300mmx17mm 150 75 75 75 75 75 125 ImmmmTmm"" mmn mm mm 50mm 100mm 100mm 50mm 19mm diameter bolts Problem (5): The tension m shown in Figur
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x 6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer
The lap joint of a tension member is shown. The plate is 252 mm wide and 12 mm thick. The bolts are 20 mm in diameter and the holes are 3 mm larger than the bolt diameter. Use A36 steel. a. Determine the safe value of P based on tension net area. b. Determine the safe value of P based on tension bearing failure. c. Determine the safe value of P based on tension block shear.