Task:Solve for the reactions..Let the force of one of theEmember be equal to "P.". (interior part)3mV 10 kNGFapply joint method of [Fx=0& {Fy=02m3m2m›consider a section andCS Scanned with CamScanner substitute P to find member forces.USC ΣΜ=015 KNT4mBnot joints

To determine reactions : ∑FX=0HA+15 = 0HA = -15 KN∑FY=0RA +…

Task: Solve for the reactions . . • Let the force of one of the E member be equal to P.". (interior part) 3m V 10 kN . apply joint method of [Fx=0& {Fy=0 G 3m 2m t • consider a section and use ΣM=0 cs Scanned with CamScanner substitute P to find member forces. 15 KN T 4m B F not joints

Task: Solve for the reactions . . • Let the force of one of the E member be equal to P.". (interior part) 3m V 10 kN . apply joint method of [Fx=0& {Fy=0 G 3m 2m t • consider a section and use ΣM=0 cs Scanned with CamScanner substitute P to find member forces. 15 KN T 4m B F not joints

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given: Consider the truss shown below and the series of loading. 20 k Required: 8⁹ An 8⁹ 8⁹ 8' 8' a 10 k 8' (A) (A) Calculate the force in member bd for case (A) (B) Calculate the force in member bd for case (B) (C) Calculate the force in member bd using the principle of superposition for the truss loading below. DO NOT use equilibrium equations. 10 k d 5 k a 8⁹ 8' (B) b 8'
The bridge is pinned at A and has a roller at G. A downward load of 12.5 lb is applied at point C, and a downward load of 25 lb is applied at E. The support reactions at the pin and roller are shown on the image. Find the stress in members making up the bridge using either the method of joints or method of sections.
The circular steel shaft is subjected to two torques as shown. The segment AB is hollow, with outside diameter of 1 inch and an inside diameter of ½ inch. The segment BC is solid, with a diameter of 1 inch. Determine (a) the maximum shear stress in the shaft, and (b) the angle of twist in degrees between A and C, using G = 12 x 10⁰ psi. 750-in. Ⓡ 2 ft 2000-in. 18 Itin. 3 ft Lin.
Situation 13 - Using method of sections, determine the internal force of members 3-6 and 5-7. Use L = 2 m and P = 3 kN. 2P P 3P 1² M 45° 45° 3 L L 45° →→X
Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.
Determine the force in member CG. The force is positive if in tension, negative if in compression. Assume F1 = 12 kips, F2 = 9 kips, F3 = 12 kips. %3D н 10° G 10' F 10' E 10' A B F, F, F, Answer: CG = i kips %3D
= The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi. Detail of joint B 3 ft (O с A 5 ft O B 6 ft D 2750 lb 3.75 in 3.75 in 0 in 0.80 Strut AB Beam CD (b Xh) Bolt (dmin) -0.50 in
Please answer with a complete solution. Thank you! The roof truss is supported by a hinge at A and a horizontal roller support at B. The wind loads are perpendicular to BC. Determine the reactions at A and B.
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.5 m, b= 1lm, d=30 mm, h= 8 mm 2а b a - a
3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F- 3190 N, a - 2.8 m, b - 5.6 m, 0 = 43°. B. a D b F Answers: AB - N AC - i N AD - i N BC - i N CD - i N
5. The rods AB and CD are made of steel. Determine their smallest diameter so that they can support the loads shown. The beam is assumed to be pin connected at A and C. Use the ASD method, where the dail=345 MPa and F.S=1.5 B D 6 kN 5 kN A 4 kN -2 m 2 m -3 m -3 m