Task I: A) Below is a list of metals and non-metals materials, Select form the list one material that is best suited for each of the following applications, and site the reason for your choice. Note: Give evidence for your reason ,Use tables whenever you can to make your answer clearer and list the physical , electrical and mechanical properties you referred to. Materials : Brass , Iron PVC , Tin , Rubber , Zinc , Aluminium. Application heat exchanger for steam. No. Material Reason 1 2 Jet engine turbofan plates. The wires of an internal engine. 3 4 The shaft of an internal engine. Cryogenic (Very low temperature container). 5 Milling machine metal base. Circuit board

Task I: A) Below is a list of metals and non-metals materials, Select form the list one material that is best suited for each of the following applications, and site the reason for your choice. Note: Give evidence for your reason ,Use tables whenever you can to make your answer clearer and list the physical , electrical and mechanical properties you referred to. Materials : Brass , Iron PVC , Tin , Rubber , Zinc , Aluminium. Application heat exchanger for steam. No. Material Reason 1 2 Jet engine turbofan plates. The wires of an internal engine. 3 4 The shaft of an internal engine. Cryogenic (Very low temperature container). 5 Milling machine metal base. Circuit board

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Dear Sir/Madam Please see attached picture. Can I have solution for this question please? Thank you, Vincent Email: vincent.smith123@yahoo.com
product properties Which of the following metals has the lowest strength? a. Zinc alloys b. Titanium alloys Oc. Magnesium alloys O d. Nickel alloys a 1)
need help engineering of materials
The class I'm taking is physics for scientists and engineers! I need help with parts E,F,G PLEASE I am completely stuck. Need help. I have attached the problem. Please view both attachments before answering. If you can please explain your answer so I can fully understand. Thank you!
Shipra Manufacturing Company is thinking about development of a strong charge producing measure by adding one-ton limit during heaters. Each clump (one ton) of charge should go through 30 minutes of heater time, including stack and dump tasks. In any case, the heater potential use factor is just 80% because of stream limitations in different pieces of the framework. Required yield for the new design is to be 16 tons for each shift (8 hours). Plant (framework) proficiency is assessed at 50% of limit. (a) Determine the quantity of heaters required. (b) Estimate the percent of time the heaters will be inactive.
Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…
STRENGTH OF MATERIALS I NEED URGENT HELP FOR MY QUESTION PLS
QUESTION 3 A Type I offshore life jacket (i.e. personal flotation device) is the type worn by commercial fishermen - it is designed for extended survival in rough, open seawater. Consider such a life jacket that uses an impermeable foam material with a density of 32 kg/m³ - the other parts of the life jacket (straps, fasteners, etc) weigh 0.6 kg and are of negligible volume to the design. a) Draw a free body force diagram for the life jacket. b) Determine the minimum volume of foam material (in L) that is needed for the life jacket in order to provide a minimum 98 N net upward force when it is fully submerged in seawater (as required by US Coast Guard regulations).
Table 1: Mechanical behavior of human cadaver tibial bones during pure torsional loads applied with the proximal tibia fixed and the torque applied to the distal tibia until there is bone fracture. Medial condyle Tibial tuberosity- Medial malleolus -Lateral condyle Head of fibula Ti-6Al-4V grade 5 Stainless Steel 316L Region of bone resection -Lateral malleolus L = 365 mm Annealed Annealed Torque at ultimate failure (bone fracture) Displacement (twist angle) at ultimate failure Torsional Stiffness Table 2: Mechanical properties of candidate materials for the rod. Material Process Yield Strength (MPa) 880 220-270 Do = 23 mm Elastic Modulus (GPa) 115 190 d₁ = 14 mm Figure 1: Representative tibia bone showing the resection region (blue arrows) and median length (L). A circular cross section of distal tibia taken at the level of resection) showing the median inner (di) and outer (Do) diameters of the cortical bone. A tibia bone after resection with the proposed metal solid rod (black line)…
1. “The grain size of metal sheet influences its formability in two opposing ways. The yield strength of a metal increases as the grain size decreases. So, the formability of a component may decrease if the grain size gets too small. Larger grained metals have better formability, but the roughened surface that results from stretching metal with grain sizes that are too large is unacceptable for many applications. During a recrystallization anneal new grains form in the metal. The final grain size depends on the annealing temperature and annealing time.” As shown in the figure below (1"x1" area under a 50Xmagnification microscope), a cold-rolled metal has been annealed at 550 degrees C for one hour. Calculate the ASTM Grain Size Number for the following condition: image attached
Need help on c ,d and e Engineering of Materials
need help with this review question Engineering of Materials I got 3,75*10-4 and 6.375*10-4 answers but there incorrect Part B