Jncct or pupci.1. What is your mechanical advantage if you are using a 35 cm wrench on a bolt that has adiameter of 3 cm?

Answered: 1. What is your mech diameter of 3

Engineering

Mechanical Engineering

1. What is your mech diameter of 3

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.3: Hand Tools

Problem 9RQ: What is one method of preventing damage to work clamped in a vise?

See similar textbooks

Similar questions

IF load : 100N and Effort force : 500N How can we calculate Fulcrum force?? Do anyone have a good ideas ?? use assumption if necessary. Thanks in advance!
What is the difference(s) between endurance limit and endurance strength? Usesketch and make the necessary assumptions.
STATICS : METHOD OF SECTIONS - GET THE GIVEN, WHAT IS ASKED, AND THE ANSWER. - MAKE A PROPER FREE BODY DIAGRAM. (IT DOES HAVE THE GREATER POINTS IN THIS ACTIVITY) - YOUR SUB ANSWERS MUST BE IN 6 DECIMAL PLACES. - YOUR FINAL ANSWER MUST BE IN 4 DECIMAL PLACES. - TELL THE DIRECTION AND WHETHER IT IS TENSILE OR COMPRESSION. - WRITE YOUR SOLUTION PROPERLY (EASY TO UNDERSTAND). - I PROVIDED A SAMPLE PROBLEM SO THAT YOU WILL KNOW HOW TO SOLVE IT. THANK YOU IN ADVANCE! Solve the forces in PQ, FL, QG, and QM. Hint: Identify all zero-force members and remove them from the structure. In the summation of moments, look for a point where member forces at the supports converge so that their moment arm is zero. From here you will be able to solve PQ. Solve FL using summation of moments from the other half of the section. Solve QG and QM using Method of Joints.
What functional problem results from torsion?
Using the figure from Question 2, imagine the lamp gets heavier and heavier until one of the cables breaks. If all of the cables have the same tensile strength, a) which one will break first, and b) why will that one specifically break first? You do not need to provide Given, Assume, and Problem Type/Features for this question. You just need to provide Find, Analyses and a Conclusion. Provide an explanation for b) that isclear, concise, correct and well organized. Use at least one diagram (2D or 3D) to make your case as to why one of them will break before the others. You can use equations/math to support your explanation as well, if you want, but expressing your answer in words and using logic will be all that is necessary. Youranswer to a) i.e. which one will break first, can be your “Conclusion” to Question 3
A hydraulic press must be used to press-fit two components together in an assembly process. The system must generate at least 975 lb of force to perform the press fit. The piston at the input cylinder is pushed with a force of 250 lb and has an area of 30 in.2. The output can use up to 15 cylinders that are each 30 in.?. How many output cylinders must be incorporated into the design? Hint (you cannot have a fraction of a tangible item - i.e. you cannot have a decimal of a cylinder)
Statics of Rigid Bodies Note: If you have already answered the problems in this post, kindly ignore it. If not, then answer it. Thank you, Tutor! Content Covered: - Method of Joints Direction: Create two problems based on the topic "Method of Joints" and then solve them with a complete solution. In return, I will give you a good rating. Thank you so much! Note: Please bear in mind to create two problems based on the topic "Method of Joints." Be careful with the calculations in the problem. Kindly double check the solution and answer if there is a deficiency. And also, box the final answer. Thank you so much!
List 3 different concepts of trenching machine design and modeling. Each concept must have an introduction and design description. Include a photo of each trenching machine design and modeling concept. For Example : an electric trenching machine
a visual inspection check and at least one test safely on components that have failed in service. Figure 1 The 220mm-long bolt was used to fasten one of the engine mount to a supporting structure. In an effort to prevent the bolt from coming loose, the torque-prevailing nut and split pin were utilized to tighten the bolt. The bolt held through an aluminum housing. Due to the reduced stiffness of the fastened parts, the bolt supported a greater proportion of the applied force. The bolt's size necessitated a high tightening torque of 660 Nm (487 Lbft). Since this level of torque could not be achieved with the tools at the time, this torque was not specified. The aluminum's maximum bearing pressure was far exceeded by the bearing stress under the nut's head and face. As a result, there was excessive preload loss due to creep. fan shaft First of all, the fan shaft was required to be made of cold-drawn 1040 or 1045 steel with a yield strength of 586 MPa and the expected life is 6440km.…
Q2(a): Stud bolt Steel plate Nut Washer Figure 2.1: Stud bolt fitting Figure 2.1 shows a stud fitting components and a steel plate. Please describe the procedure to attach the stud fittings on 2 steel plates.
Analyse, using the results, how each component failed and justify how each component’s design could be improved. Figure 1 The 220mm-long bolt was used to fasten one of the engine mount to a supporting structure. In an effort to prevent the bolt from coming loose, the torque-prevailing nut and split pin were utilized to tighten the bolt. The bolt held through an aluminum housing. Due to the reduced stiffness of the fastened parts, the bolt supported a greater proportion of the applied force. The bolt's size necessitated a high tightening torque of 660 Nm (487 Lbft). Since this level of torque could not be achieved with the tools at the time, this torque was not specified. The aluminum's maximum bearing pressure was far exceeded by the bearing stress under the nut's head and face. As a result, there was excessive preload loss due to creep. fan shaft First of all, the fan shaft was required to be made of cold-drawn 1040 or 1045 steel with a yield strength of 586 MPa and the expected…
Cutting force and frame-time, explicit calculation of reactions and diagrams