Table #2 Worktable for BCA Assay Standard Water (μl) Tube # 1 2 3 4 5 6 7 8 9 0 125 325 175 325 325 325 400 400 BSA source (μl) 300 stock 375 stock 325 stock 175 of tube #2 325 of tube #3 325 of tube #5 325 of tube #6 100 of tube #7 0 Protein (ug) Add the volumes listed in Table 2 to each tube. Add the water first and then the appropriate standard. Pipette each of the protein samples directly into the water, do not dribble on the side of the test tubes. The standard is at a concentration of 2 mg/ml and contains bovine serum albumin (BSA). Calculate the amount of BSA protein added to each of the tubes and write this in Table 2 (Protein (ug)).

Table #2 Worktable for BCA Assay Standard Water (μl) Tube # 1 2 3 4 5 6 7 8 9 0 125 325 175 325 325 325 400 400 BSA source (μl) 300 stock 375 stock 325 stock 175 of tube #2 325 of tube #3 325 of tube #5 325 of tube #6 100 of tube #7 0 Protein (ug) Add the volumes listed in Table 2 to each tube. Add the water first and then the appropriate standard. Pipette each of the protein samples directly into the water, do not dribble on the side of the test tubes. The standard is at a concentration of 2 mg/ml and contains bovine serum albumin (BSA). Calculate the amount of BSA protein added to each of the tubes and write this in Table 2 (Protein (ug)).

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

1. A wastewater sample has the following composition: NO3 = 37 mg/L as N CO3²-2.5 x 10 mol/L PO4³ = 10 meq/L Ca²+ = 75 mg/L as CaCO3(s) Express each of the above concentrations in mg/L, mol/L, meq (of charge)/L, and ppm. Make and list any necessary assumptions. Show your work and summarize the results in a table.
Question 4 What is the approximate boiling point of the liquid in the mixture with a lower boiling point? Sample Distillation Data 120 100 80 60 40 20 0 0 0.5 00 1 ● 1.5 2 2.5 3 3.5 ● ● 4 4.5
An analysis where we know what analytes we are looking for is called An analysis where we do not know what analytes are in the sample is called a An example is A) untargeted, confirmation, targeted, Comprehensive drug screen B) targeted, confirmation, untargeted, comprehensive drug screen C) targeted, comprehensive drug screen, untargeted, confirmation analysis. An example is analysis. ▪ True or false: The purpose of the internal standard is to make quantitation of the analyte insensitive to injection errors
Three labs were contracted to measure the concentration of a 5.50 ppm Ca2* standard solution. They each measured the solution 3 times, and their results are as follows: Measurement 1 Measurement 2 Measurement 3 Laboratory 1 5.47 ppm 5.54 ppm 5.50 ppm Laboratory 2 5.32 ppm 5.44 ppm 5.56 ppm Laboratory 3 5.61 ppm 5.62 ppm 5.60 ppm Select ALL of the TRUE statements about the measurement capabilities of these labs. Lab #3 was the most precise. Lab #1 was the most precise. Lab #1 was the most accurate. Lab #2 was the most precise. O.Lab #2 was the most accurate. Lab #3 was the most accurate.
Which is correct? Random errors affect accuracy and systematic errors affect precision. An accurate result shows agreement with the true or accepted value. Precise results can contain significant random error, but little systematic error. The standard deviation is a good measure of accuracy. Polydimethylsiloxane (PDMS) stationary phases have low polarities. Which of the following statements is TRUE about gas chromatography using PDMS stationary phases? The gas chromatography column is typically packed with silica microparticles. An oven is used to control the column temperature because a constant temperature is always needed in gas chromatography Octane (C8H18, boiling point: 126 ºC) is eluted later than dodecane (C12H26, boiling point: 216 ºC) 3-Pentanone ((C2H5)2CO, boiling point: 102 ºC) is eluted later than propanol (CH3CH2CH2OH, boiling point: 97 ºC)
Part A What mass of KBr (in grams) should you use to make 100.0 mL of a 1.70 M solution of KBr? Express the mass to three significant figures and include the appropriate units. m = Submit 0 μA Value Provide Feedback Request Answer Units ?
How much calcium would you ingest by drinking one 8 oz glass of your tap water? Show all calculations. Tap Water Trial 1 Tap Water Trial 2 Tap Water Trial 3 Initial Syringe Reading 1.0ml 1.0ml 1.0ml Final Syringe Reading 0.65ml 0.68ml 0.67ml Volume of EDTA Consumed 0.35ml 0.32ml 0.33ml Water Hardness ppm CaCO3 70.07 ppmCaCO3 64.064 ppmCaCO3 66.066 ppmCaCO3 Average ppm 66.73 ppmCaCO3
Data Analysis: 1. Create an Absorbance (Y) vs. Concentration (X) graph using data from the six standard solutions above. 2. Perform a linear trendline analysis of your six data points. Display the equation and R² value on the graph with a minimum of 8 decimal places. 3. On the same graph, perform a 2nd order polynomial trendline analysis of your six data points. Display the equation and R² value on the graph with a minimum of 8 decimal places. 4. Turn in your graph as the last page of this report. 5. On a separate piece of paper calculate the concentration of the unknown solution using both the linear and 2nd order polynomial trendline equations (Show all work) 6. Choose the best unknown concentration from #4 above and report it with three significant figures in the unknown data table above.
Standardization of 0.10 M HCl1. Take three (3) clean and properly labeled 250-mL Erlenmeyer flasks. Into the three flasks, weigh 0.1 g of the primary standard Na2CO3 to the nearest 0.1 mg. Record the weights of the primary standard.2. Add about 75.0 mL of boiled distilled water and swirl to dissolve the solids.3. Add 2 to 3 drops of phenolphthalein indicator. Record the initial burette reading and titrate with the prepared 0.10 M HCl solution until phenolphthalein endpoint.4. Record the final burette reading for each titration in your data sheetDetermination of Ksp and Molar Solubility1. Add Ca(OH)2 to 250.0 mL distilled water with stirring until equilibrium is achieved. 2. Filter the undissolved precipitate. Measure out 50.0 mL of the supernate into a 250-mL Erlenmeyer flask using a pipette.3. Add a few drops of phenolphthalein indicator and titrate with standardized HCl solution until endpoint is achieved.4. Record the volume the HCl solution used. Perform two more trials.…
A 1 mL microbial suspension comparable to 1 mL of 1.0 McFarland standard was subjected to a series of dilutions. An aliquot of 0.2 mL was transferred into a 100-mL volumetric flask and diluted with sterile saline solution to its final volume. Then a 0.1 mL of the resulting solution was transferred into a 50-mL volumetric flask diluted to its final volume. What would be the final concentration?
please answer fast i give upvote
f the tolerance of a 50 mL Burette is \pm 0.05 mL, which of the following would not be acceptable readings to record? 9.3 mL 43.02 ml. 22.3 mL 0.65 mL 52.45 mL 30.07 mL 15.30 mL 36.55