Table 10.5 Drainage and Water Fixture Unit Values and Minimum Pressure and Pipe Size Requirements Drainage Fixture Public or General Water closet, flushometer Water closet, gravity tank Water closet, pressure tank Urinal, flushometer Urinal, tank Lavatory Bathtub Shower Service sink Kitchen sink Electric water cooler Load Value, dfu 6 4 2 4 2 1 2 2 3 3 0.5 Minimum Pipe Diameter 4 3⁰ 3⁰ 2-3 2 2 2 2 3 2 2 Water Load Values, wsfu Cold 10 5 2 5 3 1.5 3 3 2.25 3 0.25 Hot 1.5 3 3 2.25 3 Total 10 5 2 5 3 2 4 4 3 4 0.25 Minimum at Fixture psig 20-25 8-10 25-30 15-20 8-10 8-10 8-10 8-10 8-10 8-10 8-10 Pipe Diameter 1 1/2 ¹1/2 3/4 ¹/2 3/8 ¹2 3/4 3/4 3/4 3/8

Table 10.5 Drainage and Water Fixture Unit Values and Minimum Pressure and Pipe Size Requirements Drainage Fixture Public or General Water closet, flushometer Water closet, gravity tank Water closet, pressure tank Urinal, flushometer Urinal, tank Lavatory Bathtub Shower Service sink Kitchen sink Electric water cooler Load Value, dfu 6 4 2 4 2 1 2 2 3 3 0.5 Minimum Pipe Diameter 4 3⁰ 3⁰ 2-3 2 2 2 2 3 2 2 Water Load Values, wsfu Cold 10 5 2 5 3 1.5 3 3 2.25 3 0.25 Hot 1.5 3 3 2.25 3 Total 10 5 2 5 3 2 4 4 3 4 0.25 Minimum at Fixture psig 20-25 8-10 25-30 15-20 8-10 8-10 8-10 8-10 8-10 8-10 8-10 Pipe Diameter 1 1/2 ¹1/2 3/4 ¹/2 3/8 ¹2 3/4 3/4 3/4 3/8

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need a quick solution within 15 minutes With my best wishesTon
Name three (3) type of water supply piping materials and respective type of connection joint used for distribution. a. b. Explain the function of valve and their purpose in water supply system. Briefly, list down three (3) types of valves. Briefly explain why are lift importance. Provide three reasons and explanations. a. b. For a high-rise buildings, installation are conducted by using zone systems. Explain briefly on: i. one system zone i. two system zone
This assignment was locked Mar 30 at 1pm. Prepare detailed manually prepared solutions for the following problems. 1. In a test to determine the discharge coefficient of a 50 mm by 12.5 mm Venturi meter the total weight of water passing through the meter in 5.0 minutes was 3420 N. A mercury-water differential gage connected to inlet and throat of the meter showed an average difference during that time of 38 cm. Determine the meter coefficient. Assume your own meter fluid specific gravity. 2. Considering the figure below, determine the actual discharge using the same meter coefficient as that computed from number 1. 30 cm Ø Datum Line 15 cm Ø 30 cm Water (sp. gr. = 1) 3. X 0 50 cm Gage liquid (sp. gr. = assume) 1 2 U Q
PLEASE SHOW CORRECT STEP-BY-STEP SOLUTION. THUMBS UP IF CORRECT. Thank you!
) List all the main wastewater sources that need treatment before discharge to theenvironment.
Estimate the 1998 total installed cost for the baghouse of Problem 6.4, assuming it is mild steel and is insulated, Assume the baghouse uses polypropylene bsgs with loop tops.
4
Q4: A rapid filter plant is to treat 28000 m³/d at a rate of 110 m/d. Determine the size and number of filters required. If the filtration rate is not to exceed 170 m/d with two filters being backwashed, nor 240 m/d with one filter out of service and two filters being backwashed. How much water would be required to backwash two filters if the wash is at 66 m/hr. and continues for 5 minutes.
Determine the surface dimensions and number of filters required to treat 23,000 m³/d if the rate of filtration is not to exceed 8 gallons per minute/square feet (gpm/sf).
A hall has a volume of 12500m3 and rever beration time of li5 sec if 208 Chairs Placed in the hall, what will be are additionally the new reverbration time of the hall? Conseder the absor Ption of each chair is O.1 OWa U .
A main vent pipe is to be installed to serve 4 water closets, 2 urinals, 3 shower baths, 3 wash basins, and 6 floor drains for a 10-m high residential building. Compute the total fixture units for the said building
sanitary engineering 01/ Design an intake tower with gates meets the following requirement: Bottom elevation-64 m msl, min. elevation-81 m msl normal elevation=92 m msl, max. elevation=93 m msl flow rate-1.3125 m'/s, v-0.07 m/s, coefficient of discharge (0.72), concrete density-2259 kg/m. find crown and invert elevation for all gate, and safety factor. Evaluate tower stability. 1.5m Uppr gate 3m 2.5m Gate Lower gate 1.2 m 9.4m 1.5m 2.5m [1.5m 2.5m