6.4 Using the data of Problem 6.1, design a shaker baghouse to filter 2000 m/min of air that contains 1.50 g/m³ of limestone dust. Assume that the cleaning time for one compartment is 3.0 min- utes and that the available AP, is 2000 Pa. In your design, spec- ify the filtering velocity, the number of compartments, the cloth area per compartment, and the filtration time tr.

6.4 Using the data of Problem 6.1, design a shaker baghouse to filter 2000 m/min of air that contains 1.50 g/m³ of limestone dust. Assume that the cleaning time for one compartment is 3.0 min- utes and that the available AP, is 2000 Pa. In your design, spec- ify the filtering velocity, the number of compartments, the cloth area per compartment, and the filtration time tr.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 127mm x 127mm x 12mm angle bar is connected to a gusset plate with 25mm diameter bolt as shown in…

Q: What does affect to the system if the LPC faulty (blown)?

A: LPC stands for low pressure compressor which is used in ventilation, cooling, heating, flowing of…

Q: A mechanic is reinstalling a newly-sharpened blade on a lawn mower. A wedged-in block of wood at C…

Q: 8.a. Four electricians are discussing transformer installations. Electrician A says that there's no…

A: 8 (a) Electrician A is incorrect. This is because there is a size requirement for the door sill of…

Q: Rigid insulation is available in _____ and thicknesses. Question : 1/4" and 1/2" 1/2" and 25/32"…

A: given question Rigid insulation is available in ________and ____________thickness

Q: A turbine is to operate under a head of 35 m at 300 rpm. The discharge is 10 cumecs. The efficiency…

A: Turbine operate at head of 35 m.Rotation,N=300 rpmDischarge,Q=10 cumecsEfficiency of turbine is 90…

Q: Write about Lightweight Insulating Concrete Fastener Withdrawal Test per TAS 105 Protocol procedure.…

A: TAS (Testing Application Standard) protocols are typically developed and published by regulatory…

Q: For the loaded beam shown below in Fig 4.1. Determine the reactions at the supports A and B nat will…

Q: Determine the number of plywood and 2x2 wood frame for the outdoor pad shown on the plan.Use Class A…

A: A layout of a building is shown in the figureC1 dimension = B1 dimension = CB1 dimension =

Q: What is the temperature factor, Ct, for a connection with wet in-service conditions at 120° E…

A: Given data: Connection with wet in service conditions at 120oF

Q: A.) What is the MINIMUM number of CHB units required for the Septic Tank EXTERIOR WALLS? B) What is…

A: The number of bricks required in the walls is defined as the ratio of the total volume of the wall…

Q: Exis Draw AnFud_Sfedand BiGadf yookn +8okn -80KN

Q: What is the unique feature identifying a wet-base boiler?

A: Answer Introduction The wet base boiler is used to transfer the heat of the liquid. The heat from…

Q: lote: Reference the images below to answer the question above. Assume the shingles are waste, if…

A: According to given data

Q: What is fractional efficiency curve in a sysclone seperator?

A: Cyclone separators provide a method of removing particulate matter from air or other gas streams at…

Q: A cold-storage warehouse is to be constructed of a number of individual rooms that are maintained at…

Q: 2. A rectangular concrete beam has a width of 300 mm and an effective depth of 550 mm. The beam is…

A: Answers are boxed.

Q: 6.11 A multilane highway (two lanes in each direction) is on level terrain. The free-flow speed has…

Q: For the tension member shown, determine the total service load (DL + LL) if LL = 4DL. Use A36 steel…

Q: ugo or your Jolution. - Block B hangs on a cable connected block A through a pulley as shown in the…

Q: Where does the e vibrocompaction process can be used?

A: Vibro-compaction is a technique of ground improvement, which can be used in conditions of poor…

Q: Which one of the following equations is dimensionally homogeneous? Show your proof.

Q: For a beam of cross-section, width = 230 mm and effective depth 500 mm, the number of rebars of 12…

A: Given data, For a beam of cross-section,Width,b=230 mmEffective depth,d=500 mmNumber of rebars of…

Q: An exterior wall is made up of 4" of Precast Concrete of Conductivity (K) 1.0 BTU/ in. Hr. sf °F, a…

A: The total conductivity is calculated as, K=K1+K2+...+Kn The conductivity of precast concrete is 1.0…

Q: The work done by a 1 kN of water jet moving with a velocity of 60 m/sec when it impinges on a series…

A: Given data- velocity V=60 m/s,Force F=1 kN,velocity of vanes=9 m/s,To Find-The work done by the jet.

Q: Construct the shear force and bending moment diagrams for the beam shown.Neglect the weight of the…

A: Given:- To find:- Shear force and bending moment diagram

Q: Ten #3 AWG copper load carrying conductors with type THHW, 75oC insulation are installed in a rigid…

A: Full load allowed on the #3 AWG copper conductor of type THHW 90°C insulation is 260 amps as per NEC…

Q: 1-draw the net work using AOA method 2- draw the net work using AON method Activity Predecessor A --…

A: Network diagrams in project management are used to represent different activities and also their…

Q: Discuss the effect of temperature on the fresh concrete?

A: The effect of temperature on the fresh concrete are: The setting time of fresh concrete will…

Q: A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of…

A: The offset can be calculated using the equilibrium equation. Applying moment equilibrium equation,…

Q: How thick must the insulation layer be to achieve the requirement U = 0.18 W/m2K? A wall of…

A: U = 0.18 W/m2KBearing construction = Lightweight concreteλ lightweight concrete = 0.14 W/mK, d=100…

Q: Which of the foliowing is not a method for stopping or impeding air leaks in a builiding? Installing…

A: (a) Installing house wrap: House wrap is a type of water-resistive barrier used to prevent the entry…

Q: Q/ Explain the cause of the fall of the bottom concrete cover of the roof shown in Photo No. 1 and…

A: Answer In the above diagram, the fall of the concrete cover is known as the spalling of the…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

Estimate the 1998 total installed cost for the baghouse of Problem 6.4, assuming it is mild steel and is insulated, Assume the baghouse uses polypropylene bsgs with loop tops.

6.4 Using the data of Problem 6.1, design a shaker baghouse to filter
2000 m/min of air that contains 1.50 g/m³ of limestone dust.
Assume that the cleaning time for one compartment is 3.0 min-
utes and that the available AP, is 2000 Pa. In your design, spec-
ify the filtering velocity, the number of compartments, the cloth
area per compartment, and the filtration time tr.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution:-

Step 2

Step 3 Solution:-

Step 4 Answer:-

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In rapid sand filters, the flow rate capacity is 0.3 m3/s and the filtration rate is 100 L/m2.min. When one filter is stopped the filtration rate become 150 L/m2.min. If each filter is backwashed for 5 mins and backwash rate is 60 m3/m2.hr. Find the number of filters, area of each filter, percentage of backwash water to filtered water if the filter is stopped 30 min/day. Also, find the diameter of the pipe which transport the backwash water if the designed velocity is 3m/s.
Hello You have already solved this question but correct answer is not 0.07m/sec. Please try to solve the question as per question. Thanks
4.2. The aspiration of air sampling was performed though the absorbing mass (volume 10 ml) in the mercury-vapour rectifier manufacture. 3 ml of absorbing solution was analyzed, sensitivity of the method (method determination limit) is 2 µg, maximum allowable concentration 0.00001 mg/1, (K=¹/3). K coefficient, determining the MAC portion for identification. Calculate the optimal air volume required for analysis.
The following diagram illustrates the operation of a rapid sand filter. Washwater storage tank Water level while filtering E A From coagulation larification basi 2 00 Water level while washing Filter rate controller E Lateral drain Filtered water storage tank Main drain Washwater drain The Valve D is to O 1) Control influent water from sedimentation tanks O2) Discharge dirty backwash water 3) Discard the initial filtered water after backwashing and resuming filtration 4) Control the clean backwash water 5) None of the above B3 Seal Sand Gravel 0 0 0 0 0 Caf Bottom of washwater trough Washwater rate controller
Q# 02: H1 TH H2 Toe filter H1= 12m and H2 2m Calculate head loss and head available at red, blue, green, purple and orange points.
6. In a wastewater treatment plant, a coarse screen is used. The approach velocity of the wastewater is 0.5 m/s. The velocity through the clean bar is 0.75 m/s, and the headloss coefficient for the clean bar is 0.7. i. What would be head loss for the clean screen? ii. The open area for the clean screen is 0.2 m². Determine the headloss when the clear area of the screen will be clogged by 60%. Assume the headloss coefficient for the clogged bar is 0.6.
A stack was sampled for 8 minutes. The gas velocity (at stack conditions) through the sampler was 15.0 mfs and the area of the sample probe was 5.07 cmK The net mass of particulates collected was 0,430 grams. a. Calculate the concentration of particulates in the- stack in p.g/m3.b. The temperature in the stack is 300 aF and the pressure is 725 mm Hg. If the total flow rate of gas out of the stack is 190 standard cubic meters per second* calculate the total mass emissions of particulates out of the stack in kg/day.
A raw sewage sample was brought in for total suspended solids and volatile solids analysis. A portion of the sample was poured into a tared evaporating dish and weighed. The sample was then heated at 105°C for 4 hours, weighed, heated at 550°C overnight, and weighed again. The data are as follows: • Tare wt. 42.9073g• Wt of sample 104.4680g• 105 °C wt. 45.4140g• 550 °C wt. 43.3236g What is the TSS in g/L? What percent of the solids are volatile?
Solve,
If (Qr/Q=120 percent of discharge), effluent BOD concentration=80ppm, volume of filter =825m3 , discharge =50L/sec , The influent BOD concentration equal: Choose one: a. 277.89 b. 277.2 c. 276 d. 275
i need clear ans by hand and solve very very fast in 20 min and thank you DYBALA -8 A rotary drum with a filter area of 3 m³ operates with an internal pressure of 71.3 kN/m² below atmospheric and with 30 per cent of its surface submerged in the slurry. Calculate the rate of production of filtrate and the thickness of cake when it rotates at 0.0083 Hz, if the filter cake is incompressible and the filter cloth has a resistance equal to that of 1 mm of cake. It is desired to increase the rate of filtration by raising the speed of rotation of the drum. If the thinnest cake that can be removed from the drum has a thickness of 5 mm, what is the maximum rate of filtration which can be achieved and what speed of rotation of the drum is required? The voidage of the cake = 0.4, the specific resistance of cake = 2 x 10¹2 m-2 the density of solids = 2000 kg/m³, the density of filtrate = 1000 kg/m³, the viscosity of filtrate= 10-3 N s/m² and the slurry concentration = 20 per cent by mass solids.
5. A rapid sand filter system is designed for a city with a population is 800,000 and the average water demand is estimated at 350 1/capita-day. The filter design application rate is 120 m/d- m2. i. Design the filter system (number, length and width if L/W is 1.5 and length cannot exceed 12 meters) Calculate the backwash water volume as a percent of total water treated if the backwash time is 12 minutes and rise rate is 0.5 meters/min and backwashing is done once every two days. ii.