T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for full 100 mm length on both sides. What weld size is required to give a safety factor of 3.0 if E60 series welding is used? [Ans. 10 mm] 100 mm 18KN 75 mm Note: There are two 100 mm welds.

T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for full 100 mm length on both sides. What weld size is required to give a safety factor of 3.0 if E60 series welding is used? [Ans. 10 mm] 100 mm 18KN 75 mm Note: There are two 100 mm welds.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter25: Testing And Inspection

Section: Chapter Questions

Problem 24R: What would be the transverse shear strength per inch of weld if a specimen that was 2.5 in. wide...

See similar textbooks

Related questions

Q: E70XX 1/4 V2 1/4 For the welding information shown, calculate the design capacity of the weld Rweld…

Q: 6) In the given Fig. 2, the butt-welded joint is subjected to uniaxial tensile load of 10 kN, with…

A: Given data: Load = 10 KN h= 5 mm L= 100 mm Need to determine the maximum stress.

Q: 7) For double side parallel fillet weld subjected to an external force 100 kN. The weld has throat…

A: For condition of fillet design - F = 2×0.707×t0.707×l×τ100×1000 = 2×t×l×1001000 = 2×5×ll = 100 mm

Q: 4. Design a welded connection to resist the loading shown below (service load). A double angle…

A: DL=30 k,LL=75 k,Wn=1.2×30+1.6×75Wn=156 kipsLoad on each angle=1562=78 kips=PAngle section…

Q: Calculate the heat input during the arc welding process, if the voltage is 28 volts, current is 114…

Q: Draw the Welding symbol based on the data given • SINGLE BEVEL BUTT WELD • Flat FACE • SIZE 45 mm •…

A: Given data SINGLE BEVEL BUTT WELD Flat FACE SIZE 45 mm HIDDEN SIDE ALL AROUND WELD To Draw the…

Q: A continuous fillet wild is used to weld two pieces of 7.0-mm-thick austenitic stainless steel plate…

Q: Q3 (a) What are the methods used to obtain a good weld when welding steel when the carbon content is…

A: Force ,F=60000 lbAllowable stress,Size of the weld ,h=1/4 inchTo determine:a)the method used to…

Q: The weldment shown in the figure is subjected to a static force of 100 kN. The hot-rolled steel bar…

A: (a) Calculate the weld metal strength. FW=0.7072b+dh×τallowFor electrode E6010,τallow=200…

Q: 2. A circular steel bar (50 mm) diameter and (200 mm) long is welded perpendicularly to a steel…

A: GIVEN DATA DIAMETER d=50mm LENGTH L=200mm LOAD P=5KN ALLOWABLE STRESS =100MPa WE HAVE TO FIND SIZE…

Q: Determine the size of weld,

A: Diameter = 80 mm Torsion moment = 3000 N-mMaximum shear stress in the weld not exceed = 70 N/mm2

Q: Determine the length of the weld run for a plate of size 120 mm wide and 15 mm thick to be welded to…

A: Given data: Width of the weld = 120 mm Thickness of the weld (t) = 15 mm Need to determine the…

Q: Compute for the total length of weld required with the given tension load, T. Tension member is…

Q: Material Strengths: Fy = 248 MPa, Fu = 400 MPa Method: Use ASD. A single angle L127X89X19 is welded…

A: Welding is a manufacturing method for joining materials, mainly metals or thermoplastics, by melting…

Q: The Figure shows a 0.75-in-thick AISI 1020 HR steel bar subjected to a load of (F = 1.4 kip) and…

A: Given: σy=30kpsi b=d=2in h=5/16in Load (F)=1.4kip Solution: Due to the symmetry of the weld joints,…

Q: Нome work 1. A plate( 100 mm) wide and (10 mm) thick is to be welded with another plate by means of…

A: Image_1

Q: The design below is used for a bridge construction. All parts of the assembly are made of ASTM A36…

A: P = 4000 lbOD = 4.5 inL =20 inTo find : Minimum size of weld according to table 20-4

Q: Example 27.2. A 150 mm x 10 mm by the fillet welding on three sides. The size of the weld is 6 mm.…

Q: T3.2.1The bracket shown below is to support a total load (equally divided between the two sides) of…

A: Given data as per the question safety factor = 3 Calculations T=F2(55+x)=30×103(55+22.5)=2.325×106…

Q: An axially-loaded welded angular connection is shown SD-002 . The angular section 150 x 100 x 10 mm…

Q: a) The heat energy generated at the source b) The minimum current level required in this operation…

Q: Two plates, 20 mm thick, are welded together by means of transverse-fillet welds. The ultimate…

A: Given Data Ultimate tensile strength is: sut=415 MPa Endurance limit is Se'=0.5×sut=0.5×415=207.5…

Q: 8. Design the length of weld (L) in the connection below to develop the full tensile capacity of the…

A: given t=38inch=9.525mmwidth of plate, w=6inch =152.4mmsecond palte thickness…

Q: Sketch 2 NDT symbols illustrating different methods that can be used to indicate multiple test…

A: Solution:

Q: a. Show how the extent of the surfacing weld is indicated between the vertical centerlines in the…

A: Writing the procedure to organise the weld between the lines on the flat. (1) Let us consider that…

Q: Determine the length of the weld run for a plate of size 120 mm wide and 15 mm thick to be welded…

A: We have find single transverse and double parallel fillet weld when the joint subject to variable…

Q: Two 20-mm steel plates are butt-welded together. Both the plate and the welding = 500 MPa and…

A: Given data: Plate thickness, t = 20 mm Load fluctuates from -20 kN to 60 kN Ultimate strength, Su =…

Q: 3.) The diagram below shows a 5.5m long double angle brace which is connected by 6mm welding…

A: given data

Q: 7. Determine the size of fillet welds required for the weld group shown in fig. 10.21.

Q: What is the safety factor for this weld? F=671 Ibf, b=1 in; d=2.2 in; h=1/4 in. The weld metal is…

Q: Two plates, 25 mm thick, are welded together by means of transverse-fillet welds. The ultimate…

A: Given Ultimate tensile strength Sut.=415 MPa Surface finish factor ka=0.5 Size factor kb=0.85…

Question

T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for
full 100 mm length on both sides. What weld size is required to give a safety factor of
3.0 if E60 series welding is used? [Ans. 10 mm]
100 mm
18kN
75 mm
Note: There are two 100 mm welds.
1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please help me my home work thank you
8. Design the length of weld (L) in the connection below to develop the full tensile capacity of the plate. Use E70 electrodes and 1/4" side fillet welds. The material is ASTM A36 Steel and the allowable axial tensile stress is 22,000 psi. (show all your work) "L" PL 1/2" PL 3/8" x 6" P
i need the answer quickly
Solve correct
3.) The diagram below shows a 5.5m long double angle brace which is connected by 6mm welding connection. The length of weld shown in the picture is 300 mm on the top and 100 mm on the bottom. The 2-L127x 89x6.4 are 300W steel and long leg back-to-back. The braces are to be welded to a 12 mm 350W steel gusset plate. Determine the factored tensile capacity of the angles. Any intermediate connections that are required should also be specified. 740 kN -12 mm Gusset Plate
appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in).
None
Q2: Two plates, 25 mm thick, are welded together by means of trans verse-fillet welds. The ultimate tensile strength of a weld metal is 415 MPa. The surface finish factor of the weld surface is 0.5, and the size factor is 0.85. The reliability is 90%. Determine the length of the weld if the factor of safety is 2. The transverse force on the welds is 100 kN, which is completely reversed under fatigue loading. Take: A=10mm 25 A Toe
Hi, I need help with this question.
7) For double side parallel fillet weld subjected to an external force 100 kN. The weld has throat thickness of 5 mm and the measured shear stress is found to be 100 MPa. From the above given information find out the length of the welded joint desigN? O 100 mm 50 mm 25 mm 10 mm
Please show work correctly,if not sure skip.
Question No. 11: (a) Illustrate flatness, straightness and circularity with symbol. (b) A circular shaft, 80 mm in diameter is welded to support by means of a circumferential fillet weld. It is subjected to a torsion moment of 3000 N-m. Determine the size of weld, if the maximum shear stress in the weld is not to exceed 70 N/mm2 . (c) Analyze different stresses during design of screw and nut