Suppose you use an ideal pulley of the type shown in the figure below and find it necessary to exert a force of 310 N to support a load. MA-3 (a) What is the load's mass (in kg)? kg (b) What force (in N) is exerted on the ceiling? Neglect the pulley system's mass. N (upward)

Suppose you use an ideal pulley of the type shown in the figure below and find it necessary to exert a force of 310 N to support a load. MA-3 (a) What is the load's mass (in kg)? kg (b) What force (in N) is exerted on the ceiling? Neglect the pulley system's mass. N (upward)

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Shown in the figure below is a system of two blocks. One of these blocks is resting on a surface tilted left and the other one is on a surface tilted right. The strings and the pulley have no mass. There is no friction anywhere in the problem.The characteristics of the system are given here: m1 = 4.14 kg m2 = 6.69 kg ?1 = 23.0 ?2 = 57.7 Answer all the following:What is the normal force, N1, on mass m1? What is the normal force, N2, on mass m2? What is the acceleration, a of the system? What is the tension, T?
14 5a
7) Suppose you use an ideal pulley of the type shown in the figure below and find it necessary to exert a force of 240 N to support a load. MA - 3 (a) What is the load's mass (in kg)? kg (b)What force (in N) is exerted on the ceiling? Neglect the pulley system's mass. N (upward)
The force F in the figure keeps the 8.3 kg block and the pulleys in equilibrium. The pulleys have negligible mass and friction. Calculate the tension T in the upper cable. T
1 A person exercises the quadriceps as shown. The diagram on the right shows a model of the leg, where the person's lower leg of length L = 0.60 m is held at an angle 0₁ = 60° with respect to the horizontal. The quadriceps muscle exerts a force FM via the tendon that attaches to the tibia at a distance d = 0.10 m from the knee, in order to lift a weight of mass m₁ = 5.91 kg that is attached to the foot. The tendon makes an angle of 0₂ = 11.5° with respect to the tibia. 2 What is the force required to hold the weight at the position shown in the diagram? Assume the person's lower leg weighs 150 N and its centre of mass is located at a distance L/2 from the knee. Round your answer to the nearest Newton. FM M d- 02 01 m₁
The figure below shows a claw hammer being used to pull a nail out of a horizontal board where ? = 27.3°. The mass of the hammer is 1.00 kg. A force of 165 N is exerted horizontally as shown, and the nail does not yet move relative to the board. Assume the force the hammer exerts on the nail is parallel to the nail. A hand uses a hammer to pull a nail out of the ground. The head of the hammer is curved and touches the ground at a single point of contact at the center of the head. The nail in the ground makes an acute angle ? clockwise from the vertical. The nail is hooked in the hammer claw 5.00 cm horizontally to the left of the hammer head's point of contact to the ground. The hand pulls the hammer handle horizontally to the right 30.0 cm above the ground with a force vector F.(a) Find the force exerted by the hammer claws on the nail.magnitude kNdirection ° above the horizontal (b) Find the force exerted by the surface on the point of contact with the hammer head.( î + ĵ)…
The pulley system shown in Figure Q1b lifts a mass, m, of 250 kg. Calculate the force FA necessary to maintain the suspended mass in static equilibrium; and determine the forces at the ceiling anchor points A and B.
a) For each of the weightless and frictionless pulley systems (a) to (e) in Figure Q5a: Determine the tension (T) required to lift and hold a 1450 N crate in static equilibrium for each of the pulley systems (a) to (e). Use g = 9.81 m/s2 and give your answers in newtons (N) to two decimal places. (i) Determine the ideal mechanical advantage (IMAPulley) for each of the pulley systems (a) to (e). (ii) (iii) Determine the reaction force where the pulley wheel is connected to the ceiling for each of the pulley systems (a) to (e). Use g = 9.81 m/s² and give your answers in newtons (N) to two decimal places. (a) (b) T (c) T (d) T (e) T
Directions: Assume, unless otherwise specified, that all numbers have at least 3 significant figures. F (N) Students collect data, see graph, for the force involved in stretching a rubber band. The data is well fit by the equation F = 33.65 x0.4971, 12 10 where F is in newtons and x is in meters. One end of the rubber band is attached to a stationary vertical rod and the other end to a 0.3 kg mass. The mass rests on a frictionless horizontal surface. The mass is pulled back such that the rubber band is stretched by 0.8 m from its unstretched length and then released from rest. 4. x (m) 0,1 0.02 0.04 0.06 0.08 A. What is the speed of the mass after it has traveled 0.4 m? B. What is the maximum speed of the object?
A diving board of length 3.00 m is supported at a point 1.00 m from the end, and a diver weighing 550 N stands at the free end (Figure 1). The diving board is of uniform cross section and weighs 270 N. For related problemealing ting and strateginn Figure K-1.00 m- -2.00 m 1 of 1 ▼ Part A Find the magnitude of the force at the support point. Express your answer in newtons. VG ΑΣΦ Fsupport Submit Part B = Request Answer ? N
I need Part A and Part B
The maximum force in each rod can not exceed 1540 N Figure 1m 14 12 m 3 m 2m 1m 2m O 2 m 3m Part A Determine the greatest mass of the crate that can be supported. (Figure 1) Express your answer to three significant figures and include the appropriate units. Wmar = Submit HA Value < Return to Assignment 4 Request Answer ✔ Units Provide Feedback wwww ? D