Suppose a circuit is required to recognize the 4-bit pattern (1100), and the output (z=1) whenever it occurs in the continuous serial input (X) of the circuit. 1- Draw the mealy state diagram. 2- Write down the state table. 3- Check state reductions. 4- Assign binary values to the states. 5- Obtain the binary-coded state table. 6- Select the T flip-flops in your design.

Suppose a circuit is required to recognize the 4-bit pattern (1100), and the output (z=1) whenever it occurs in the continuous serial input (X) of the circuit. 1- Draw the mealy state diagram. 2- Write down the state table. 3- Check state reductions. 4- Assign binary values to the states. 5- Obtain the binary-coded state table. 6- Select the T flip-flops in your design.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the equivalent logic circuit diagram of the following expressions : a. XY = F b. X + Y = F XÝZ = F c. d. XY + XZ = F e. XYZ + XÝZ = F
The following statements describe the sequential circuits. Select all the TRUE statements. a The sequential circuits consist of a combinational circuit and storage elements. b The storage elements keep a binary bit even though the circuit power is gone. c Only the current input determines the outputs of sequential logic circuits. d The flip-flop is controlled by signal levels.
You are asked to construct a multi-function shift register with the functionality shown**: Design a one bit circuit which implements the functionality. Use D flip flops and any logic gate and/or combinatorial circuit seen in class. Label all inputs and outputs.
Design counter that counts from 00 to 59, using the IC 74LS90 ripple counter and use two 7 segment display to display the result count. You can also use 7447 binary to 7-segment Display Decoder in logicworks.
The objective of the activity is to determine the design of the logic gates for the BCD to a 7 segment display. You do not need to implement your design. 1. Show the truth table for BCD to 7 segment display. (4 bit input, with all outputs, a-g and the corresponding decimal digit) 2. Show the K-map and minimized boolean function for each output. 3. Show the logic diagram of the decoder. (You may use a CAD for this or if you do not have one, you may submit a handwritten one.) This is a very common decoder and there are many sites covering requirements 1-3. However, it would be best if you go through the design by hand as an exercise from the truth table to don't cares in K-maps.
A limited company has four directors A, B, C, D holding 35%, 30%, 20% and 15% of the shares respectively. A major decision must have a support of minimum 60% of the stock. Design a combinational logic circuit for the voting in the company. Use a decoder to design the circuit. Show the truth table of the circuit.
Please design a 6:1 multiplexer following the below procedures with data inputs of D5, D4, D3,D2, D1, D0 and output of Y.1 How many select signals are needed for this Mux.2) List a truth table for this Mux. Note: for all the unused combinations of select signals, Y=D5Develop an optimized function for this Mux.4Sketch the logic diagram of implementing this 6:1 Mux. Write a complete VHDL structural model to implement the above 6:1 multiplexer. Assume allthe required sub-component (standard gates) VHDL models are given/known that you can use.
1. Design a combinational logic circuit that compares two 4-bit numbers A and B. The circuit should output the relation of the two inputs. Use an available TTL IC for the design.
considering a logic circuit to transmit information, which has three input signals (group of bits) and a control signal. The circuit is capable of generating an output bit that corresponds to even parity or odd parity, if the control signal is activated (´1´) the output corresponds to the generation of the even parity bit. The parity bit is sent with the input signals. Determine the corresponding minimum circuit.
Using the state transition table below, construct a sequential circuit based on JK Flip flops and any logic gate seen in class. Derive simplified equations for the flip flop inputs as well as for the output Z.
Problem: Design a binary counter with the following repeated binary sequence: Use JK-type Flip-Flops. 0, 1, 2, 3, 4, 5, 6, 7 1. Draw the state diagram and derive the next-state table. 2. Fill in the K-map to find the minimum SOP expression for the functions JA, KA, JB, KB, JC and KC. 3. Draw the logic diagram of the circuit.
For a sequential logic circuit that detects 010011 sequences in binary information received from an external input line x and makes external z output 1 when detected; a) Create the state diagram. Explain how you created it. b) Create the situation table. Note: D flip-flops are used in this circuit. If there are unused states in the state table, you can specify the next state values and output them as inactive values.