1. How many maximum opposing force/s can apin support react against applied forces?1O 22. It describes the roughness or smoothness ofthe surfaces.Angle of frictionCoefficient of frictionFrictionNormal force3.4.

Maximum opposing force can a pin support react against applied force is 2 Pin or hinge support…

Answered: support react against applied forces? 1…

Engineering

Civil Engineering

support react against applied forces? 1 2 3 4 escribes the roughness or smoothness of surfaces. Angle of friction

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve any Problem on flexure stress formula for beams
The triangular plate is deformed into the shapeshown by the dashed line. Determine the normalstrain developed along edge BC and the averageshear strain at corner A with respect to the x and yaxes.
Consider the beam below. If the beam is subject to a 20kN internal shear force, determine the maximum shear stress (in MPa) in the beam. The thickness of all pieces is 30mm.
A reinforced concrete beam has a width of 400 mm and a total depth of 550 mm. The longitudinalbars at the top are 2 – 28 mm Ø and 4 – 32 mm Ø at the bottom. Concrete strength is f’c = 24 MPaand steel yield strength fy = 300 MPa. Steel cover is 70 mm. 8. What is the transformed moment of inertia? a. 3548.65 x 106 mm4 b. 3768.19 x 106 mm4 c. 3535.63 x 106 mm4 d. 3024.58 x 106 mm4 9. What is the moment capacity? a. 204.11 kN.m c. 284.34 kN.mb. 215.29 kN.m d. 201.75 kN.m10. What is the safest uniformly distributed load that the beam can carry if the length of the beam is 8 meters? a. 35.54 kN/m c. 22.08 kN/mb. 25.22 kN/m d. 26.91 kN/m
Complete answer
Please answer the following question in the picture and make sure you draw a free body diagram also use positive sign convention for internal forces please, Thank for your help. Post pictures of your work instead of typing it.
a) create a free body diagram of the truss and determine the external forces at the supports b) isolate joint a (method of joints) c) isolate joint c (method of joints) d) isolate joint d (method of joints) e) check results by isolating joint b (method of joints) f) summarize your results in a force diagram
Subject : Mechanics of materials Give me right solution urgent please If the applied shear force V = 19,573 lbs, determine the maximum horizontal shear stress (in ksi) acting on the member. Use x = 2 inch, y = 5 inch.
A wooden beam is fabricated by nailing together three boards as shown. The boards have dimensions of b1 = 20 in., d1 = 1.2 in., b2 = 1.2 in., d2 = 19 in., b3 = 10 in., and d3 = 1.2 in. The vertical distance from the bottom edge of the section to the centroid is 12.761 in. The moment of inertia of the section about the z axis is 4113 in.4. Determine the maximum shear stress in the cross section if the internal shear force is V = 440 lb. Assume that the shear force V acts in the y direction. The maximum shear stress will occur at the centroid. Cut a cross section along the centroidal z axis and calculate the first moment of area at this section.
8 kN 4 m 15 kN 5 kN 2 m 2 kN 2 m 2 m A B с D E The aluminum rod shown has a diameter of 20 mm and is subject to axial forces acting at A, B, C, and D. Assume the rod has a Young's modulus of E = 70 GPa. a) State the internal axial forces within sections AB, BC, CD, and DE. Remember to indicate whether they are in tension or compression b) What is the displacement of A relative to C? c) What is the displacement of A relative to E?
The question is in the picture. Thanks
H.WE A bar with Constant aoss-section arealAl and unit weight (8) is subjected to axiai force (P) in addition to it: own weight, find the total Clengation?